Discuss methods of transport planning process

Reference no: EM131456419

Aims and Objectives

The highways part of the module aims to provide students with a basic understanding of highway design and construction, an understanding of the practices associated with highway route selection, the analysis of traffic flows, vehicular behavior, highway capacity and related issues of environment and sustainability.

Outcomes:

1. Discuss methods of transport planning process and highway planning strategies.
2. Apply and evaluate methods of analysis of highway traffic and signalized intersections.
3. Evaluate the principles of highway alignment, and carry out geometric design and intersection designs, including environmental aspects.

Introduction:

The road network of any city is its lifeline and the evaluation of their performance is very necessary for future traffic planning, design, operation and maintenance. Traffic congestion is the common problem of most urban area in Oman; most of the roads are congested.
The following project should be solved individually. In the project, students will have hands-on experience in discussing methods of transport planning process, evaluate methods of analysis of highway traffic and signalized intersections, and carry out geometric design and intersection designs.

Transport Planning and Geometric Design of Highway

1. Task I

The AASHTO publication A Policy on Geometric Design of Highways and Streets provides the standards for geometric design of highways. It is planned to construct a rural collector highway between Muscat and Nizwa in in an area of rolling terrain

1. Describe the three categories of information about the characteristics of the area of a proposed highway location that can be assembled in the office prior to any field survey activity.

2. To determine the ADT on the road, the data was collected as shown below on a Tuesday during the following.

Table 1: Traffic volume at specific time

7:00-8:00 a.m.	8:00 -9:00 a.m	9:00-10:00a.m	10:00-11:00 .m	11:00 -12 noon
150	120	130	50	20

3. In this situation, determine the following design values.
i. Minimum design speed
ii. Recommended lane width
iii. Preferable shoulder width
iv. Right of Way
v. Maximum grade
I. Determine the minimum length of a crest vertical curve and sage vertical curve if the grades are

Table 2: grades for the curve

Up fill grade	Down fill grade
+4	-2

Consider the following for the sage vertical curve criteria :(a) Stopping sight distance,(b) Comfort
(c) General appearance

2. Task II

1. For a 4.5 mi two-lane highway segment in level terrain in Muscat. Determine the PTSF If

Table3: Traffic characteristics of the Segment.

Traffic volumes (two- way) veh/h

Trucks %

RVs%

PHF

directional split

no-passing zones

1100

10%

0.97

60/40

40%

2. Estimate the ATS for.

Table4: Geometric characteristics of the Segment.

Speed	lane width	shoulder width	access point
56	11	3	12

3. Compute: LOS, v/c, veh-mi in peak 15 min and peak hour, and total travel time in peak 15 min.

4. Describe the traffic characteristics associated with the LOS for your two-lane highways.

5. Using the previous data, determine PTSF and ATS in the peak direction if northbound volume = 1000 veh/h and southbound volume 600 veh/h.

6. Finally determine the level of service of a two-lane section if a passing lane 1.5 mi long is added. The passing lane begins 0.75 mi from the starting point of the analysis segment.

3. Task III

1. You have been hired as a consultant to a medium-sized city to develop and implement a procedure for evaluating three alternatives to replace an existing two-lane highway with a four-lane highway that will meet current design standards are proposed. The selected alternative will provide a more direct route between two towns that are 12.0 miles apart along the existing highway. With each alternative operating speeds are expected to be at or near the design speed of 60 miles per hour. Develop the scores for each alternative and recommend a preferred alternative for development. The following scoring method, developed by the transportation oversight board, is to be used

Table 5: Ranking and Weights for Each Objective

Evaluation Criterion	Performance Measure	Weight (%)
Mobility	Travel time of shortest travel time alternative divided by travel time of alternative i	25
Safety	Annual reduction in number of crashes of alternative i divided by highest annual reduction in number of crashes among all alternatives	25
Cost- effectiveness	Annual reduction in number of crashes of alternative i divided by highest annual reduction in number of crashes among all alternatives	20
Environmental impacts	Annual reduction in number of crashes of alternative i divided by highest annual reduction in number of crashes among all alternatives	15
Community impacts	Number of business and residences displaced by least impacting alternative divided by number of businesses and residences displaced by alternative i	15

The following information has been estimated for each alternative by the planning staff:

Table 6: Estimated Values for Measures of Effectiveness

Property	Alt. 1	Alt. 2	Alt. 3
Cost of development	$10,900,000	$18,400,000	$16,900,000
Length	11.2 miles	9.8 miles	10.1 miles
Annual crash reduction	10	17	19
Business displacements	3	4	5
Residential displacements	4	3	3
Wetlands impacted	1.5 acres	3.9 acres	3.9 acres

2. Write a short report for a comparative evaluation of the impacts of the project on Social and Natural Systems

2 Intersection Design

Task I

a. Describe the different principles involved in the design of at-grade intersections and the different types of at-grade intersections. Also, give an example of an appropriate location for the use of each type.

b. A minor road intersects a multilane divided highway at 90° forming a T intersection. The speed limits on the major and minor roads are 55 and 35 mi/h, respectively.

- Design the minimum sight distance required for a single-unit truck on the minor road to depart from a stopped position and turn left onto the major road. Discuss additional consideration should be given to the sight distances computed for the design vehicle crossing the intersection.

- For the design determine the sight distance required by the minor-road vehicle to safely complete a right turn onto the major road.

- Discuss the changes if the intersection is an oblique intersection with an acute angle of 35°.

Table 7: characteristics of the intersection

Major Road ml/hr	Minor Road ml/hr	Type of vehicle	Angle
55	35	Single unit truck	35°

2. Task II

1. Design a suitable signal phasing system and phase lengths for the intersection using the Webster method. Show a detailed layout of the phasing system and the intersection geometry used For the geometric and traffic characteristics shown below.

Table 8:The geometric and traffic characteristics of the intersection

Approach (Width)	North (56ft)	South (56 ft)	East (68ft)	West (68ft)
Peak hour approach volumes
Left turn	133	73	168	134
Through movement	420	373	563	516
Right turn	140	135	169	178
Conflicting pedestrian volumes	900	1200	1200	900
PHF	0.95	0.95	0.95	0.95

Assume the following saturation flows:

Table 9: The saturation flow of the intersection

Through lanes veh/ln/h

Through and right lanes veh/ln/h

Left lanes veh/ln/h

Left and through lanes veh/ln/h

Left, though, and right lanes veh/ln/h

saturation flow rates

1600

1400

1000

1200

1100

2. If saturation flow rates that are 10% higher. What effect does this have on the cycle length?

3. Task III : Evaluating the Alternatives

1. Three designs have been proposed to improve traffic flow at a major intersection in a heavily traveled suburban area. The first alternative involves improved traffic signaling. The second alternative includes traffic-signal improvements and intersection widening for exclusive left turns. The third alternative includes extensive reconstruction, including a grade separation structure. The construction costs, as well as annual maintenance and user costs, are listed in the following table for each alternative. Determine which alternative is preferred based on economic criteria if the analysis period is 20 years and the annual interest rate is 15%. Show that the result is the same using the present worth, equivalent annual cost, benefit- cost ratio, and rate-of-return methods.

Table 9: Cost and Benefits for Improvement Plans with Respect to Existing Conditions

Alternative

Capital Cost ($)

Annual Maintenance Cost ($)

Annual User Cost ($)

Salvage Value ($)

Present condition

15,000

500,000

Traffic signals

440,000

10,000

401,000

15,000

Intersection widening

790,000

9000

350,000

11,000

Grade separation

1,250,000

8000

301,000

2. You are asked to develop and implement a procedure for evaluating the previous project, write a short report describing your proposal and recommendation as to how the city should proceed with this process.

3 Parking Design

1. Briefly describe the tasks should be included in a comprehensive parking study for your college campus, describe how you would perform each task and the way you would present the data collected.

2. Select a parking lot on your campus. For several hours, conduct a study of the lot using the methods described in this chapter. From the data collected, determine duration, turnover, Occupancy, Parking capacity, and Efficiency. Draw a parking accumulation curve for the lot.

3. Select a parking lot on your campus (specify with illustration), calculate total number of Cars that park between 8 a.m. and 4 p.m or 4:00pm to 8:00 pm.

I. Calculate the percentage of these cars that park for an average of 2 hr, 4hr, 6hr, and 8hr.

II. Determine the space-hours of demand at the lot.

III. If 10% of the parking bays are vacant on average (between 8 a.m. and 12 p.m.) at the parking lot, determine the number of parking bays in the parking lot. Assume an efficiency factor of 0.85.

IV. MEC is planning an expansion of her lot to provide adequate demand for the following 5 years. If it has been estimated that parking demand for all categories will increase by 5% a year, determine the number of additional parking bays that will be required.

Table 10: percentage of parking demand and parking bay

% of parking bay	parking demand %
10	5

Attachment:- Highway and transportation engineering.xlsx

Reference no: EM131456419

Questions Cloud

In which way are tsunamis similar to wind-generated waves : In which way are tsunamis SIMILAR to wind-generated waves? Which statement best describes how longshore currents are generated?

How sample is needed if the desired margin of error is given : According to Thomson Financial. through January 25. 2006. the majority of companies reporting profits had beaten estimates (BusinessWeek. February 6. 2006).

Necessitating new structural designs for organizations : Briefly list and describe 1 major change necessitating new structural designs for organizations.

Customers dealing more directly with the company : What is meant by customers dealing more directly with the company? What are examples of this? How does increasing customer satisfaction increase market share?

Discuss methods of transport planning process : Discuss methods of transport planning process and highway planning strategies - Apply and evaluate methods of analysis of highway traffic and signalized intersections.

Estimate the current proportion of health care insurance : The percentage of No not covered by health caw insurance in 2003 was 15.6% (Si/nis-i/cc/Abstract of the United States. 2006).

Pay system reform and technology : Select two topics (Pay System Reform and Technology) and discuss two positive effects and two challenges the topic poses for human resource departments.

Discuss about the confederation and constitution : As depression struck the new nation in the mid-1780s, new questions arose about the nature of American democracy.

Adequate transportation services : When conducting property analyses, hospitality managers should ask themselves certain questions if they want to attract meeting and convention business.

Reviews

len1456419

4/10/2017 1:24:41 AM

dear sir i want from you to do this Coursework for me ,first i need the sublimation of the proposal on 13/04/17 and the full Coursework on 20/05/2017 i have uploaded 2 files first one is the guideline and second file excel the date needed to do the Coursework thank you

len1456419

4/10/2017 1:24:09 AM

Good Quality 70-79% (Merit) Identification and very good understanding of issues in the assessment. Full answers to all questions/task. Very clear argument with relevant examples used to illustrate response. Clear evidence of reading outside the module list. Few errors in referencing or grammar or syntax as appropriate Acceptable 60-69% (Pass) Good understanding of the issues. Engages directly with the question. All significant content accurate. Clear argument with good examples used to support it. All main points and important issues of the question/task covered. Some evidence of reading outside the module list. Some small repeated errors in referencing or grammar or syntax as appropriate

len1456419

4/10/2017 1:24:00 AM

Outstanding 90-100% (Outstanding) Focused and comprehensive engagement with the question, showing evidence of in-depth understanding of the issues. Extremely clearly structured and demonstrating a coherent argument throughout. Evidence of wide, independent reading. No obvious errors in referencing or grammar or syntax as appropriate. Excellent 80-89% (distinction) Detailed response to all relevant parts of the question with evidence of clear understanding of the issues. Well-structured with evidence of independent reading supporting the argument. Very few errors in referencing or grammar or syntax as appropriate.

len1456419

4/10/2017 1:23:24 AM

3. Research Methods: Describe how the research will be conducted. Identify methods of collecting data. Provide diagrams of experimental equipment to be built. Identify analytical methods to be use (give references). Provide maps showing locations of field sampling stations. Develop the theory of modeling studies. Identify sources of information and numerical methods you will use to complete your study, including a complete explanation of the methods of data collection, experimental set- ups, analysis methods, and statistical tools that will be used to analyze the data. Include a detailed description of all of the major steps of the study, the assumption you will make, and the limitations of the methods you will use. 4. Expected Results: Include a detailed discussion of any calculations or experiments you have already completed, as well as what new results are expected from your proposed study in this section. Restate the significance of the proposed work here. 5. References: References should be presented using the same formatting style as will be used in the final project/thesis/dissertation.

len1456419

4/10/2017 1:23:14 AM

2. Introduction: General description of the problem under consideration Clear statement of the research question or hypothesis to be addressed Clear statement of the research objectives General summary of the methods that will be used to achieve the objectives. The introduction begins with a general discussion of the topic area and then a statement of your specific hypothesis. The significance of the question(s) to be addressed and the impact the proposed work will have on these questions should be addressed. A short statement about how the rest of the proposal is organized is sometimes included in this section. a. Background or Literature Review: Provide a thorough review of relevant information that has been done on the topic. This should include a summary and analysis of published literature and reports. b. Objectives: This section describes what work will be done. Also, the goals and the objectives of the work to be performed may be described in this section.

len1456419

4/10/2017 1:22:59 AM

The proposal does not have to be lengthy but must adequately convey what the project will cover and what the deliverables will be. Consider this proposal as a one you would submit to get hired for an actual contract. Basically, the proposal should clearly tell the client what they will be getting if you are hired to do this work. The organization of a research proposal is usually very simple. It should have the following components: 1. Summary: The abstract is a concisely written summary of the that includes the hypothesis statement, a brief discussion of background information, scope and objectives of the proposed work, methods to be used, expected results, and the study’s significance.

len1456419

4/10/2017 1:22:27 AM

Follow the guidelines mentioned below during writing your case study: ? The report should have a Title Page. Title Page should contain the following information. ? Title ? Class ? Student name ? Student ID ? Submitted to ? Use page numbers ? Use your own words on writing, Times New Roman font size 12 ? Heading should be with Font Size 14, Bold, Underline ? Use Diagrams and Examples to explain your topic.

len1456419

4/10/2017 1:22:16 AM

Note: This submission should include full solutions including calculations for each of the problems presented. All solutions should clearly state any assumptions, clauses, tables, figures and formulas used • Student should submit a proposal for the CW with a maximum of 10% of the assessment marks Report Format • Number of pages: Maximum 15 pages including references list and the appendix (if any). • Line spacing: Generally use 1.5 x line spacing. • Start with the title page (including your name) or student number as requested. • It is preferable to place figures within the text rather than group them at the end of the report. • Give a sequential number to all figures (Fig. 1, Fig. 2, Fig. 3, etc.) • Add a brief, informative caption to the figures.

len1456419

4/10/2017 1:21:48 AM

1. Discuss methods of transport planning process and highway planning strategies. 2. Apply and evaluate methods of analysis of highway traffic and signalized intersections. 3. Evaluate the principles of highway alignment, and carry out geometric design and intersection designs, including environmental aspects.

Write a Review

Required(*) Message

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

User Account

All Pages