Discuss applying the safety and health management systems

Assignment Help Other Engineering
Reference no: EM132455084

This assignment involves completing two exercises, and the purpose is for you to apply the safety and health management systems approach to workplace ergonomics.

Discussion 1: Relating Countermeasure Strategies

Question1: Discuss the 10 generic countermeasure strategies proposed by Haddon as they relate to an incident that might have occurred on your worksite, or relate the countermeasures to something you have observed.

The 10 generic countermeasures are listed below:

(a) Prevent the initial buildup of energy.

(b) Reduce the potential energy.

(c) Prevent the release of the energy.

(d) Reduce the rate of release of energy.

(e) Separate the host from the energy source.

(f) Place a barrier between the host and energy source.

(g) Absorb the energy.

(h) Strengthen the susceptible host.

(i) Move rapidly in detect and counter the release.

(j) Take procedures to ameliorate the damage.

  • Your response should be at least 200 words in length.

Discussion 2: Applying the Safety and Health Management Systems Approach to Workplace Ergonomics

  • This question involves reading the following passage, choosing one side of the debate, and then defending your choice by providing your rationale. Read the following passage and then decide who is at fault: the company or the employee.
  • Our truck driver, Ben, injures his back while tying down the tarps on his flatbed trailer. He has to use four-inch straps to secure the load, and then has to cover the load with tarps which require the use of bungee cords (rubber straps) to secure the tarp.
  • Either defend the company and decide that the root cause for the back injury was due to the failure of the employee to properly follow the processes and procedures, or defend the employee and decide that the root cause of the back injury was due to the failure of the company to provide a hazard-free workplace. To successfully answer this question, you might have to do a bit of research. Consider the following sources: the OSHA standards, the Federal Motor Carrier Safety Administration (FMCSA) rules

Reference no: EM132455084

Questions Cloud

Discuss quality control and inspection : Briefly address how the pressure from the manager impacts Ben's ability to successfully perform his job-what are the emotional and psychological
Applicability of the fighting words doctrine : In oral argument, Justice Scalia questions the applicability of the "fighting words" doctrine enunciated in Chaplinsky v. New Hampshire , 315 U. S. 568 (1942).
Define and describe the apa documentation system : Define and describe the APA documentation system in one paragraph. Don't write as if you are a student. Write in your role as an editor in a publishing
Discuss why your mineral is valuable by explaining : Discuss why your mineral is valuable by explaining how your mineral is used in its mineral form. Try to compare and contrast its industrial uses
Discuss applying the safety and health management systems : Applying the Safety and Health Management Systems Approach to Workplace Ergonomics, Discuss the 10 generic countermeasure strategies proposed by Haddon
Difference between job satisfaction-organizational : Compare the difference between job satisfaction and organizational commitment. Determine which is more strongly related to performance for your selected company
Deliver a basic proposal for project : By the end of week 2, student interns are expected to deliver a basic proposal for their project answering the following questions:
Calculate the balance of retained earnings : Calculate the balance of Retained Earnings that would appear on a Balance Sheet at December 31, 2012. Calculate the gross profit percentage
Describe the budget you will need to support your project : Last week, you were given the mantles of a project. You have properly defined your project. Now, it is time to estimate your budget.

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd