User Account

All Pages

Direct strip casting and conventional thick slab casting

Assignment Help Mechanical Engineering
Reference no: EM132641370

Between direct strip casting and conventional thick slab casting, please explain briefly:

(1) Which one produces sheets with minimum secondary processing,

(2) Which one produces sheets with minimum segregation of alloying elements.

Reference no: EM132641370

Questions Cloud

Examples the main activities of management : Identify with examples the main activities of management. What do you see as the main attribute(s) or qualities required of a manager in undertaking
Argue your support for the decision of the court : Research articles on computer trespass or computer hacking cases from within the past three years. Next, argue your support for or against the decision.
Give two examples of cash receipts : Give two examples of cash receipts and two examples of cash payments that fit into each of the Operating activities and Investing activitiesclassifications
What is the purpose of the exclusionary rule : The purpose of this case study is to research and complete a thorough analysis of the Exclusionary Rule. Your paper will summarize the Exclusionary Rule.
Direct strip casting and conventional thick slab casting : Between direct strip casting and conventional thick slab casting, please explain briefly:
How any computer software recognised as an intangible asset : How any computer software recognised as an intangible asset by Norfolk Ltd would be measured on initial recognition and subsequent to initial recognition
Discuss about the allied health community media : Complete the following assignment using the Allied Health Community media provided in the study materials. Open the Allied Health Community media application.
Define working environment elements : How would you assess risk in terms of severity of risk. How would you assess risk in terms of probability of risk.
Determine the amount that newark ltd should recognise : Determine the amount that, in your judgement, Newark Ltd should recognise as a provision as at 30 June 2020. Justify the approach

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Capital structure

Long-Term debt, with an incremental borrowing rate of 8% and capital stock, with the information.

  Write a scilab script named prob_01.sce

ENGR 112: Write a Scilab script named Prob_01.sce, that takes no inputs and returns the vectors below.Use the colon operator to create a vector starting with -9 and ending with 52 in increments of 0.5.Use the linspace function to create a vector of l..

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  Air is adiabatically compressed in a non flow process from

air is adiabatically compressed in a non flow process from a pressure of 14.7 psia and temperature of 70 degrees to 200

  A pitching wedge a golfer is using gives the ball a initial

A pitching wedge a golfer is using gives the ball a initial angle of 50 degrees, what range of velocities (Vo) will cause the ball to land within 3 ft of the hole?

  Heat transfer at the phase front may be characterized by an

a spherical cryosurgical probe may be imbedded in diseased tissue for the purpose of freezing and thereby destroying

  The diameter of the upper shaft is d = 20 mm

Determine the maximum tensile, compressive, and shear stresses at point B, which is located on the surface of the shaft at the y0 axis.

  Question regarding the systems development process

1. Why is system integration a particularly critical part of the systems development process? Suggest three sociotechnical issues that may cause difficulties in the system integration process.

  Determine the mass flow rate

Air enters a one-inlet, one-exit control volume at 6 bar, 500 K, and 30 m/s through a flow area of 28 cm2. At the exit, the pressure is 3 bar, the temperature is 456.5 K, and the velocity is 300 m/s. The air behaves as an ideal gas. For steady-sta..

  Why might you not be receiving the new rate of pay

After receiving your next paycheck, however, you realize that you were paid at the previous rate of pay. Why might you not be receiving the new rate of pay?

  Similar to the rolling direction of anisotropic sheet metal

A drawn, thin -walled tube has plastic (orthotropic) anisotropy. The axial direction of the tube is similar to the rolling direction of anisotropic sheet metal. The tube diameter is 3 inches and the wall thickness is 0.040 inch.

  Exit to the mixing chamber water is saturated water vapor

Superheated steam at 400°C and saturated water with a quality of 40% enter a mixing chamber at a pressure of 100 kPa. What is the required ratio of mass flow rate of superheated steam to mass flow rater of saturated water if at the exit to the mixing..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd