User Account

All Pages

Different types of adaptor

Assignment Help Mechanical Engineering
Reference no: EM13888764

Using examples, illustrate the different types of adaptor needed to support sequential composition, hierarchical composition, and additive composition.

Design the interfaces of components that might be used in a system for an emergency control room. You should design interfaces for a call-logging component that records calls made, and a vehicle discovery component that, given a post code (zip code) and an incident type, finds the nearest suitable vehicle to be despatched to the incident.

Reference no: EM13888764

Questions Cloud

What impact does the violation have on the surrounding : What impact does the violation have on the surrounding community?
Major technical and nontechnical factors : What are the major technical and nontechnical factors that hinder software reuse? Do you personally reuse much software and, if not, why not?
Independent certification authority : It has been suggested that an independent certification authority should be established. Vendors would submit their components to this authority, which would validate that the component was trustworthy.
Determine the target cost per unit for the filter : Krystal Water is considering introducing a water filtration device for its 20-ounce water bottles. Determine the target cost per unit for the filter.
Different types of adaptor : Using examples, illustrate the different types of adaptor needed to support sequential composition, hierarchical composition, and additive composition.
Validate a reusable component : Explain why it is difficult to validate a reusable component without the component source code. In what ways would a formal component specification simplify the problems of validation?
Find and critique an empirical article : Find and critique an empirical article in which a factor analysis was used to build a leadership/organizational instrument (scale) that was published in a peer-reviewed leadership journal. Then, start the dialogue by critiquing the selected resear..
Program elements and components : 1. What are the fundamental differences between components as program elements and components as services? 2. Why is it important that components should be based on a standard component model?
What the legal challenges were for the slaves in the amistad : what the legal challenges were for the slaves in the Amistad case

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Its specific heat ratio is 14 and gas constant is 0287

an open brayton cycle engine operates with a compressor-pressure ratio of 6 an inlet temperature of 20 c and inlet

  The liquid condensate is removed from the system at 60o f

atmospheric air at 90o f and 60 relative humidity flows over a cooling coil at an inlet volumetric flow rate of 2000

  A heavily insulated piston-cylinder device contains 005 m3

a heavily insulated piston-cylinder device contains 0.05 m3 of steam at 300 kpa and 150 degrees celcius. steam is now

  Design a process to produce a 05 cm-diameter steel shaft

design a process to produce a 0.5 cm-diameter steel shaft having excellent toughness yet excellent wear and fatigue

  Determine the distance between a and b after 3 minutes

two ships a amp b are moving at constant velocities. at t0 the position of ship a is 2.41 miles east and 3.14 miles

  If the cylinder is to be protected against excessive

a hydrogen tank 25 cm in diameter and 80 cm in height is charged to 150 atmospheres at room temperature 25 c. a

  A manometer connected to the tap shows a head of 014 in of

a jet of air from a nozzle is blown at right angles against a wall in which a pressure tap is located. a manometer

  The tank is not very well insulated after many hours the

a rigid tank is filled with refrigerant r-134a at 310 k. an electric current of 0.2 amps over 220 volts is passed

  The water leaves the pump at a pressure of 14mpa and a

water at a temperature of 40 c and a pressure of 100 kpa enters a pump at the rate of 50000 kghr. the water leaves the

  Consider the surface of a solid that is at an elevated

consider the surface of a solid that is at an elevated temperature and exposed to cooler surroundings. by what modes is

  A ball is projected vertically with a velocity

A ball is projected vertically with a velocity of 40m/s. Three seconds later, a second ball is projected vertically with a velocity of 30m/s. At what point in the air will these balls meet?

  The acceleration of a particle is defined by the relation

the acceleration of a particle is defined by the relation a25-3x2 where a is expressed in ms2 and x in meters. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd