Difference between the actual gain and ideal gain

Assignment Help Electrical Engineering
Reference no: EM131206989

(a) An inverting amplifier with resistors R1 = 5.6 k and R2 = 120 k is fabricated using an op-amp with an open-loop gain of 105. What is the percent difference between the actual gain and the ideal gain?

(b) Repeat part (a) if R1 is changed to R1 = 8.2 k.

Reference no: EM131206989

Questions Cloud

Manufacturing overhead cost expressed on per unit basis : If 10,000 units are produced, what is the total amount of manufacturing overhead cost incurred to support this level of production? If 10,000 units are produced, what is the total amount of manufacturing overhead cost expressed on a per unit basis?
What is the maximum rms value of an input sine wave : An op-amp is connected in an inverting amplifier configuration with a voltage gain of -80 and is biased at ±5 V. If the output saturates at ±4.5 V, what is the maximum rms value of an input sine wave that can be applied without causing distortion ..
Total amount of variable costs related to the units sold : If 14,500 units are sold, what is the total amount of variable costs related to the units sold? If 10,000 units are produced, what is the average fixed manufacturing cost per unit produced? If 14,500 units are produced, what is the total amount of fi..
Product on periodic inventory system : The annual demand for a product on periodic inventory system is 50,000 units; the replenishment lead time is 9 days. The review period has been established as 16 days.
Difference between the actual gain and ideal gain : An inverting amplifier with resistors R1 = 5.6 k and R2 = 120 k is fabricated using an op-amp with an open-loop gain of 105. What is the percent difference between the actual gain and the ideal gain?
Preparing an interpretive action research project : Review 5 major steps of preparing an Interpretive Action Research project. How does it differ from Experimental Survey research?
Explain the places and artifacts that the tourists will see : Imagine you are narrating a guided tour throughout the ancient Greek and Roman worlds. Create a 700- to 1,050-word tour guide describing the places and artifacts that the tourists will see.
Chart of accounts for exact wording of account titles : Lowe Manufacturing Co. warrants its products for one year. The estimated product warranty is 8% of sales. Assume that sales were $520,000 for January. In February, a customer received warranty repairs requiring $180 of parts and $70 of labor. Require..
How long waveform will take to complete five cycles : If a periodic waveform has a frequency of 20 Hz, how long (in seconds) will it take to complete five cycles?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What must the gain ofthe second stage be in db

Two stages are cascaded to result in an overall gain of 680 V/V.The loaded gain of the first stage is 36 dB. What must the gain ofthe second stage be in dB to satisfy this specification In V/V

  Calculate the currents in various sections

3-phase ring main ABCD fed at A at 11 kV supplies balanced loads of 50 A at 0.8 p.f. - Calculate the currents in various sections and station bus-bar voltages at B, C and D.

  Determine the heat removal rate per unit

A novel design for a condenser consists of a tube of thermal conductivity 200W/m · K with longitudinal fins snugly fitted into a larger tube. Condensing refrigerant at 45°C flows axially through the inner tube, while water at a flow rate of 0.012 ..

  Determine what must the unity gain of the op amp be

It is required to design a noninverting amplifier with a dc gain of10. When a step voltage of 100 mV is applied at the input, it isrequired that the output be within 1% of its final value of 1 V inat most 100 ns. What must the unity gain of the op..

  Determine the sum or difference of two numbers

Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.

  What is the value of the total circuit complex impedance

An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 100 ohm, inductor L = 40 mH, and capacitor C = 0.5 F. The value of the total circuit complex impedance is

  Why flux in primary and secondary winding of the transformer

Why Flux in Primary and Secondary Winding of the Transformer is Same? With a Simple Explanation and Example.

  Calculate the power received

The figure shows a circuit with five elements. If p1 = -209 W, p2 = 66 W, p4 = 26 W calculate the power p3 received or delivered by elements 3.

  Explain what effect a resistance has on voltage of circuit

the nature of resistance and expalin why the resistances are not exactly what the color code says it is. Also, explain what effect a resistance has on the voltage of a circuit, as well as the current.

  Discuss the differences between series and parallel circuits

Discuss the differences between series and parallel circuits. What are some advantages and disadvantages of each type Discuss why the total power equals the sum of the individual values of power, whether a series circuit or a parallel circuit is u..

  Assignment develop a sensor circuit using commodity

assignment develop a sensor circuit using commodity componentsnbspthe first part of the assignment is to design a

  What is the change in the total voltage across three diodes

what is the change in the total voltage across the three diodes?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd