User Account

All Pages

Develop equations which may be solved to give the final

Assignment Help Mechanical Engineering
Reference no: EM13344385

Develop equations which may be solved to give the final temperature of the gas remaining in a tank  after the tank has been bled from an initial pressure PI to a final pressure P2. Known quantities are  initial temperature, tank volume, heat capacity of the gas, total heat capacity of the containing tank, P1,  and P2. Assume the tank to be always at the temperature of the gas remaining in the tank, and the tank  to be perfectly insulated. 

Reference no: EM13344385

Questions Cloud

The stomach to give carbon dioxide water and a soluble : a certain brand of antacid chewing gum was sent to the lab for testing and it was found to have 15 by mass of
If you used the 8900 kilojoules you expend in energy in one : if you used the 8900 kilojoules you expend in energy in one day to heat 51000 of water at 20 what would be the rise in
Once released into the atmosphere the so2 is likely to : once released into the atmosphere the so2 is likely to react with oxygen to form so3. what can happen next if the so3
Calculate the number of moles of gaseous n2 contained in a : calculate the number of moles of gaseous n2 contained in a sample of 300 ml of gas saturated with water vapour at 25
Develop equations which may be solved to give the final : develop equations which may be solved to give the final temperature of the gas remaining in a tank nbspafter the tank
A sample of 142 g of helium and an unweighed quantity of : a sample of 1.42 g of helium and an unweighed quantity of oxygen are mixed in a flask at room temperature. the partial
In the commercial manufacture of nitric acid how many : in the commercial manufacture of nitric acid how many liters of nitrogen dioxide will produce 30 liters of nitric oxide
The following times to failure in hours were observed in an : the following times to failure in hours were observed in an experiment where 14 units were tested until eight of them
What is the minimum number of bits required to represent : what is the minimum number of bits required to represent each of the following decimal numbers 10 1000 100000 and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Saturated water at mean temperature 20 degc flows inside a

saturated water at mean temperature 20 degc flows inside a 25-mm-idnbspcircular tube which is electrically heated to

  Compute the atomic packing factor

the unit cell for uranium has orthorhombic symmetry, with a, b and c lattice parameters of 0.286, 0.587 and 0.495nm, respectively. if its density, atomic weight, and atomic radius are 19.05g/cm3, 238.03g/mol and 0.1385 nm respectively, compute the..

  Determine the normal force r between the wheel

Determine the normal force R between the wheel and the horizontal surface. Neglect the weight of the horizontal shaft.

  Detemine the normal and shearing stresses

Knowing that the pipe has inner and outer dimensions equal to 35 and 42 mm, respectively, detemine the normal and shearing stresses at point a and point b.

  Determine the magnitude of its acceleration

The car travels up the hill with a speed of v = (0.4s) m/s, where s is in meters, measured from A. Determine the magnitude of its acceleration when it is at point s = 50 m, where p = 500 m.

  Calculate the height h to which the ball rises

A ball is thrown vertically up with a velocity of 91 ft/sec at the edge of a 190-ft cliff. Calculate (a) the height h to which the ball rises and (b) the total time t after release for the ball to reach the bottom of the cliff.

  Calculate average velocity and mass flow rate of air

wall temperature needed for the runner to cylinder #3, such that the cylinder air inlet temperature is the same as that in cylinder #1. Runner length for cylinder #3 is 15 cm.

  Determine expressions for attractive and repulsive energies

determine the expressions for attractive and repulsive energies, EA and ER as a functions of r where r is in nm and E is in eV.

  Determine the speed at which it strikes the ground at b

the snowmobile is traveling at 10m/s when it leaves the embankment at A.determine the speed at which it strikes the ground at B and its maximum acceleration along the trajectory AB.

  Design a container using differentiation

design a container using differentiation that has a volume of 2500 litres. it must use the minimum amount of material.

  What is the pressure in the tank

If 300 Kg of air is pumped into a previously empty 100 m^3 tank, and the temperature of the air in the tank is 25 deg C, then what is the pressure in the tank in N/m^2?

  Find the angular velocity of link cd

(a) Find the angular velocity of link CD and the velocity of the pin relative to the slot in link CD. (b) Find the angular acceleration of link CD and the acceleration of the pin relative to the slot in link CD.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd