Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
the display has ten light bulbs going up apole and we want one light per second to illuminate ( with previous one turning off ), starting from bulb 9 at the bottom of the pole, and ending with bulb 0 at the top. The controller sets E=1 when the countdown begins in the last ten seconds, and then counts down from 9 to 0 in binary.
1).To develop contoller as a sequential circuit using minimum number of D flip-flops and the minimum number of external gates. the controller should set the values of the control lines appropriately to drive the combinational logic circuit.
2).To design combinational logic circuit that controls the light bulbs using minimum number of 2*4 decoders and minimum number of external gates.Also to draw schematic diagram consisting of flip-flops, decoders and external circuitry.
What is the thermal noise level of a channel with bandwidth 10kHz carrying 1000. Watts of power at 50o C?
Resisitive load, A 4:1 step down transformer uses a 60Vac source on the primary windings.
Develop the pseudo-code below for a program that will retrieve 2 bytes (NUM1 and NUM2) from memory, determine which is closest to the numeric value 50, and indicate the result by setting a variable named "CLOSEST" to 1 (if 1st byte is closest) or ..
Modify the state diagram branching conditions in the diagrams below as needed to ensure the sum and exclusion rules are obeyed in each case.
A TTL gate with VIH (min) = 2.25 V and VIL (max) = 0.65 V is being driven by a gate with VOH (min) = 2.4 V and VOL (max) = 0.4 V. What is the maximum amplitude of noise spikes that can be tolerated on the inputs in both the HIGH and LOW states
Consider a series RLC circuit disconnected from a source at t=0. The circuit components are R=3 ohms, C = 500 F, and L = 1 H. We assume that Vc(0-) = 20 V and i(0-) = -0A. a) Find the natural reponse i(t) for t > 0.
During the cyber security activity conducted in class by Renee Etoty, you were asked to identify systems that were conducting or experiencing cyber attacks. You will use the data provided during this activity to develop a program to display.
Analysis of link budget DTH QPSK Satellite link, A direct-to-home satellite television system uses a geostationary satellite in orbit above the equator at a longitude of 109 degrees west.
our senior design team is designing a force sensor to measure a force signal and analyze the signal with a microcomputer (binary system). The analog force signal is between 10 N and 70 N and has the frequency bandwidth of DC - 1000 Hz.
Two points are given P1 (1,0,1) and P2 (6,-3,0) Calculate: a) The scalar components of the vector pointing from P1 to P2. b)The scalar components of the vector pointing from the origin to P1. c) The magnitude of the vector pointing from P1 to P2 ..
Transfer function : key informaiton, A linear time-invariant discrete-time system is excited by the input x[n] = d[n] + 2u[n-1] (d represents δ(delta)). The resulting output response with zero initial conditions is y[n] = ((0.5)^n * u[n]). De..
If I have a resistor that is 10 Ohms and has a voltage drop of 4.2 V, how much current is flowing through the resistor?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd