Develop an equation for the velocity exiting the pipe

Assignment Help Mechanical Engineering
Reference no: EM13827251

Problem-

Given the following fluid system, where both the top and bottom tanks are open to the atmosphere and there are two piping paths from the top to the bottom tank path A and path B, that join at point C prior to discharge into the bottom tank at point D.

893_fluid system.jpg

-Known quantities: all pipe segments have the same diameter, "D" and the same roughness factor, "f"

-Assume incompressible, isothermal flow of a Newtonian fluid.

-Both elbows have the identical friction loss coefficients, Kel

-The discharge nozzle at point D has a friction loss coefficient of Kdn

-Other dimensions are shown on the diagram.

a. Assume that the valve on line B is closed. Develop an equation for the velocity exiting the pipe, point D, in terms of known quantities (indicated on the figure or in the assumptions, listed above).

b. Assume that the valves on both lines A and B are fully open and that the friction loss coefficient of the tee at point C is zero. Is the pressure drop through line A (from the tank to point C) greater than, equal to, or less than the pressure drop through line B (from the tank to, point C). Explain the reasoning you use in. choosing your answer. 

c. Assume that the bottom tank is totally enclosed and that the pressure inside the tank is maintained at pressure P1 Assume that the valve on line A is closed. Develop an equation for the velocity exiting the pipe D, into the tank at point D in terms of known quantities.

Additional information-

The problem related to Mechanical Engineering and it is about fluid systems. Two tanks in a fluid system are filled with fluid. Many questions about this fluid system have been solved in the solution with detailed computation.

Reference no: EM13827251

Questions Cloud

Asset turnover ratio-return on assets-profit margin on sales : The 2011 Annual Report of Tootsie Roll Industries contains the following information. Compute the following ratios for Tootsies Roll for 2011. Asset turnover ratio, Return on assets, Profit margin on sales
Financial analysis of a project : In your role as strategic management accountant, you have completed a financial analysis of a project. The project is:
What technological needs are appropriate for police and why : How may over-use of technology repeat history for police and crime. How is surplus military technology consistent with community-oriented policing
Determine transaction price of arrangement for aaron : John’s Agency sells an insurance policy offered by Capital Insurance Company for a commission of $90. In addition, Aaron will receive an additional commission of $30 each year for as long as the policyholder does not cancel the policy. Determine the ..
Develop an equation for the velocity exiting the pipe : Assume that the valve on line B is closed. Develop an equation for the velocity exiting the pipe, point D, in terms of known quantities
Writing a letter of advice to a senior finance manager : You are to select an organization and prepare an assignment on how risk management is practiced in that organization.
What the gross margin percent for the department : If the Gross margin dollars for the men's department at a local department store are $875,197 and the department net sales are $ 1,592,630 what the gross margin percent for the department?
Review and reflection crimes against property : How did participating in discussions help your understanding of the subject matter? Is anything still unclear that could be clarified?
Prepare the intangibles section of carters balance sheet : On January 1, 2014, because of recent events in the field, Carter estimates that the remaining life of the patent purchased on January 1, 2013, is only 5 years from January 1, 2014. Prepare the intangibles section of Carter’s balance sheet at Decembe..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The front of a jet engine acts as a diffuser receiving air

the front of a jet engine acts as a diffuser receiving air at 900 kmh -5degc 50 kpa bringing it to 80 ms relative to

  Determine the mass of the steam

A 2m^3 rigid insulated tank initially containing saturated water vapor at 1 MPa is connected through a valve to a supply line that carries steam at 400C. Now the valve is opened, and steam is allowed to flow slowly into the tank until the pressure in..

  What is the minimum plate length that should be used at

a fan that can provide air speeds up to 50ms is to be used in a low-speed wind tunnel with atmospheric air at 25 degc.

  Neglecting kinetic and potential energy effects determine a

a rigid tank has a volume of 60 liters and initially contains a two-phase liquid-vapor mixture of h2o at a pressure of

  Assuming that no energy is lost in the impact determine a

a 100 gram ball moving at a speed of 7.4 ms strikes a 1.1 kg plate supported by springs. assuming that no energy is

  What is value of convective heat transfer coefficient

what is value of convective heat transfer coefficient for pebble glass in air medium?

  Assume the regriderator works in a carnot cycle between -10

a refridgerator should remove 500 kj from some food. assume the regriderator works in a carnot cycle between -10 and 45

  Determine the work and energy destruction for nitrogen

Three kilograms of nitrogen (N2) initially at 47C and 2 bar is contained within a rigid, insulated tank. The nitrogen is stirred by a paddle wheel until its pressure doubles. Employing the ideal gas model with constant specific heat evaluated at 300K..

  A first class lever in static equilibrium has a 50lb

a first class lever in static equilibrium has a 50lb resistance force and 15lb effort force. the levers effort force is

  A particular road vehicle weighs 4000 lb using the

a particular road vehicle weighs 4000 lb. using the quarter-car model determine a suitable value for the suspension

  Five hundred cubic feet per second of water flow in a

five hundred cubic feet per second of water flow in a rectangular open channel 20 ft wide and 8 ft deep. after passing

  If the power generated by the turbine is 75 mw determine

steam expands in a turbine steadily at a rate of 36048 kgh entering at 8 mpa and 600degc and leaving at 20 kpa as a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd