User Account

All Pages

Develop a physical design for the intersection

Assignment Help Civil Engineering
Reference no: EM132418883

HCS Project

Due to the development of a new regional shopping center, a major new intersection must be provided for significant movements into and out of the shopping center. The main entrance to the shopping center is on the North side of the intersection. The expected demands for the new intersection are given below. There will be 3% trucks into and out of shopping center and 1% trucks everywhere else. There are 20 buses per hour stopping on the right side of each approach in all directions except leaving the shopping center, which has zero.

784_figure.jpg

The tasks for this project are as follows:

Task 1. Develop a physical design for the intersection, that is, how many lanes and what channelization for the lanes.

Task 2. Develop a complete signal timing plan - assume a pre-timed signal.

Task 3. Using HCS software, run an HCM analysis of how the intersection is expected to operate under the proposed design and signal timing. You may not have any lane groups with LOS of E or F. You do not want lane group v/c ratios greater than 0.95

Task 4. The fewer lanes you use and still keep a LOS of D or better, the higher your grade.

Task 5. Make sure the design works in the simulation

Verified Expert

The paper was on the practical design of a physical intersection.The problem requires special consideration and determination of the number of lanes that will efficiently manage traffic flow in and out of a shopping center.Special consideration was on the total flow of traffic through the shopping centre and vehicles which do not have to go through the shopping centre.

Reference no: EM132418883

Questions Cloud

Media strategy and message strategy : Media strategy and message strategy- What are some intended outcomes for the brand from an IBP perspective?
Research and development activities and they will contribute : Describe your research and development activities and explain how they will contribute to the company and Discuss how your company's activities will affect
Dsicussion about how to start a community initiative : A student has approached you with a concern or problem that they have identified in his or her community or school. In order to prevent falling into the trap.
Drop in value of a share of summit systems : What is the drop in value of a share of Summit Systems stock based on this? information?
Develop a physical design for the intersection : Develop a physical design for the intersection, that is, how many lanes and what channelization for the lanes and Develop a complete signal timing plan
Data for measuring beat frequency in procedure and analysis : Explanation of data: the first folder contains the data for measuring beat frequency in procedure and analysis (c).
Determine the amount of factory overhead : Use this information to determine the amount of factory overhead that was (over) or under applied.
Create an atmosphere that sparks young people aspirations : Creates an atmosphere that sparks young people's aspirations. Digs deep and incorporates key elements of authentic youth involvement by making sure.
Determine the total manufacturing costs : Use this information to determine the total manufacturing costs incurred during the fiscal year 2018.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Give the phase and the missing property of

Give the phase and the missing property of P, T, v and x. Put the values in a table withcolumns P, T, v, and x.

  Determine the vertical reactions at the supports

Two boards each having the same EI and length L are crossed perpendicular to each other as shown. Determine the vertical reactions at the supports. Assume the boards just touch each other before the load P is applied.

  Find the final temperature

A constant pressure container is filled with 1 kg of stainless steel and 0.5 kg of PVC (polyvinyl chlo- ride) both at 20C and 0.25 kg of hot air at 500 K, 100 kPa. The container is now left alone with no external heat transfer.

  Find hp per foot of cutting edge ratio for all 4-conditions

The Caterpillar D6R Series 3 and D8R tractors are rated, respectively, at flywheel horsepowers (fwhp) 0f 185 and 305. The "A," "S," and "SU" blade widths (length) for the D6R are S, 16 ft, 9 in.; A, 17 ft, 1 in

  Detremine the cfat in year 0 for the challenger and defender

The defender had a first cost of $300,000, but its market value now is only $100,000. It has chargeable expenses of $120,000 per year and no expected salvage value. To simplify calculations, assume that SL depreciation was charged at $60,000 per y..

  Find the total energy cost and savings from cfl bulbs

A CFL bulb that puts out as much light as a 60-W incandescent bulb might costs $10, compared to about $1 for the incandescent bulb. But CFL bulbs are expected to last (on average) 15,00 hours, compared to about 1000 hours for an incandescent bulb.

  Define what is master plan

Define what is Master Plan - List the effects of this proposed project on the environment by keeping in view the deifintion of the "environment" under the Environmental Assessment Act;

  Find the hydraulic conductivity of the aquifer

A confined aquifer 30 m thick has been pumped from a fully penetrating well at a steady rate of 5000 m3/day for a long time. Drawdown at an observation well 15 m from the pumped well is 3.0 m

  What is discharge revised discharge pressure of compressure

A compressor installed at a whalf (for loading container ships) is able to provide 6 bar.g pressure into the pressure reciever. The compressor is moved to a site that is 5000 ft above sea level (atmospheric pressure 0.85 bar.a

  Design speed station of pc station of pt deflection angle

A horizontal Curve is designed for a two lane mountainous terrain. The following data are known. intersection angle: 40 degrees tangent length: 436.76 ft Station on PI: 2700+10.65 fs=0.12 e=0.08

  Find percent reduction at each stand

A continuous hot rolling mill has eight stands. The dimensions of the starting slab are: thickness = 3.0 in, width = 15.0 in, and length =10 ft.

  What is the absolute pressure at the surface of the mercury

An airplane is flying at 10.6 km altitude. in its nonpressured cargo bay is a container of mercury 325 mm deep. The container is vented to the local atmosphere.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd