Develop a fsm for a priority arbiter

Assignment Help Electrical Engineering
Reference no: EM131201590

An arbiter is a circuit that allows at most one subsystem at a time to use a shared resource. A four-way arbiter is shown in Figure 4.48. Each subsystem sets its request signal to 1 when it wants to use the resource. When the arbiter sets the grant signal to 1, the subsystem uses the resource. The subsystem sets its request back to 0 when it has finished, and waits for grant to be 0 before starting a subsequent request. While a subsystem is granted use of the resource, other requests must wait, rather than pre-empting the active subsystem.

a) Develop a FSM for a priority arbiter, in which subsystem 0 has highest priority and subsystem 3 has least priority. A pending request from a higher-priority subsystem takes precedence over a pending request from a lower-priority system.

b) Develop a FSM for a round-robin arbiter. Subsystems are granted requests in order, starting with 0, then 1, 2, 3 and back to 0. A subsystem is skipped if it has no pending request.

1981_b6c4f379-66de-4e9a-b81a-18459debbe7d.png

Reference no: EM131201590

Questions Cloud

Explain how to stop invidious comparison : Identify strategies you currently use to avoid vicarious traumatization in your personal life. Will those strategies help you avoid vicarious traumatization as a human services worker?
Develop a verilog model of the sequential multiplier : In Chapter 3, we showed how to perform multiplication of unsigned integers by addition of partial products. Construct a multiplier for two 16-bit operands containing just one adder that adds successive partial products over successive clock cycles..
Explain the identified changes to the suppliers : Explain the identified changes to the suppliers in such a way that they will understand the standards that BP requires in order to maintain their relationship with the company.
Construct a three-year binomial interest rate tree : Using a value of 10% for the volatility of the one year forward rate, construct a three-year binomial interest rate tree with one year forward rates.
Develop a fsm for a priority arbiter : Develop a FSM for a priority arbiter, in which subsystem 0 has highest priority and subsystem 3 has least priority. A pending request from a higher-priority subsystem takes precedence over a pending request from a lower-priority system.
What is the maximum clock frequency : If the path with a delay of 1.3ns is optimized to reduce its delay to 800ps, what is the maximum clock frequency for the optimized datapath?
Formulate a linear programming model : The Rays can produce no more than 24 dozen jars of relish. They make $2.25 in profit from a jar of chow-chow and $1.95 in profit from a jar of tomato relish. The Rays want to know how many jars of each kind of relish to produce to generate the mos..
What herzberg would categorize as motivational factors : Job satisfaction is achieved through what Herzberg would categorize as motivational factors rather than hygiene factors (status, salary, job security, types of supervision, etc.).
How does a scientific theory differ from a regular theory : How is a scientific hypothesis different from a scientific theory? How does a scientific theory differ from a regular theory (i.e., a non-scientific theory in the way the term is used by lay people)?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the current flowing through resistor

Apply Mesh Analysis to calculate the current flowing through Resistor R2 in the below sketch:

  Find an appropriate values for le and it

Design a linear DC motor for propelling and braking a track-guided vehicle. The vehicle contains a generator to power the electromagnet with current Ic for the generation of the flux density B. The track region carries a current . Assume that the ..

  What is the output power of the system using a motor powered

A student lifts a weight (W) using a motor powered by solar cells to determine the efficiency of the solar cell/motor system. On the power meter the voltage reads V and the current reads I. The student lifts the weight a distance H in a time T.

  Find the probability of bit errors occurring in the frame

Let the probability of a bit error be p, and the length of a data frame be N. Find the probability of 1, 2, 3, and 4 bit errors occurring in the frame. a) Tabulate the results for N = 1000, 10000, and 100000 bits, for p = 10-6, 10-8, and 10-14

  Evaluate required received power that achieves a bit error

Data at a rate of 2 Mbps is to be transmitted via a pass-band communication system whose carrier frequency is 500MHz. A binary antipodal system with roll-off factor of 0.2 is used for this communication. The AWGN single-sided power spectral densit..

  Determine the net chage delta q that flowed through resistor

Determine the net chage delta Q that flowed through a resistor over teh specified time interval for each of the following currents: (a) i(t) = 0.36A, from t=0 to t=3s (b) i(t) = [40t +8] mA, from t=1s to t=12s

  Find the gain kp necessary to meet the requirements

A proportional control system is to be used to control the wing flap of a jet airplane. The wind load is expected to cause as much as 600 in-lb of torque. The system should be able to keep the flaps with 5o of the set point.

  Compare and contrast two of the rfc types identified

To familiarize yourself with the Internet Standards, search the Internet for the IETF RFC website. Using the information you find on this site, answer the following questions: Identify four types of Internet standards.

  Find the equivalent resistance of the given one-port

A LINEAR ONE-PORT IS MODELLED WITH A: 10V AT LOADRESISTANCE=10kilo ohm AND :0.5mA WITH LOAD RESISTANCE=100kiloohm. Find the equivalent resistance of the given one-port.

  Make a block diagram for a resonator

Make a block diagram for a resonator. Where the forward path element G(s) is an amplifier.- What does the feedback element H(s) consists of?

  Find what is the average current drain from the battery

Suppose that we are designing a cardiac pacemaker circuit. The circuit is required to deliver pulses of 1-ms duration to the heart, which can be modeled as a 500 ohm resistance. The peak amplitude of the pulses is required to be 5 V.

  Determine the voltage gain

An amplifier produces an output voltage of 2v for an input of 50mv.- If the input and output currents in this condition are 4mA and 200mA, determine the voltage gain.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd