Determne the angular velocity at the instint theta

Assignment Help Civil Engineering
Reference no: EM13306501

When theta=0 degrees , the assembly is held at rest, and the torsional spring is untwisted. If the assembly is released and falls downward, determne the angular velocity at the instint theta=90. Rod Am has a mass of 6 kg, and disk C has a massof 9 kg. Length of AB is 450mm, the radius of the disk is 75mm, k=20 Nm/rad

Reference no: EM13306501

Questions Cloud

Determine the rise in temperature of the rock : A rock of mass 0.210 kg falls from rest from a height of 20.8 m into a pail containing 0.429 kg of water. determine the rise in temperature of the rock
Find out the transfer function : proper rational system alone,with initial conditions on its input and output Input is a step signal with arbitrary value. Calculate and Plot all the above using MATLAB writing a code.
Compute the coefficient of volume expansion of the liquid : A flask is filled with 1.58 L (L = liter) of a liquid at 100 °C. When the liquid is cooled to 13.3 °C, What is the coefficient of volume expansion of the liquid
Write a program that creates two vectors from x-one : write a program that creates two vectors from x-one (call it P) that contains the positive elements of x, and a second (call it N) that contains the negative elements of x. In both P and N, the elements are in the same order as in x.
Determne the angular velocity at the instint theta : When theta=0 degrees , the assembly is held at rest, and the torsional spring is untwisted. If the assembly is released and falls downward, determne the angular velocity at the instint theta=90.
Find the change in the period of the heated pendulum : A simple pendulum consists of a ball connected to one end of a thin brass wire. find the change in the period of the heated pendulum
What must average speed of the car be during the last min : During the first 18 minutes of a 1 hour trip, a car has an average speed of 11 m/s. What must the average speed of the car be during the last 42 minutes of the trip to be if the car is to have an average of 21 m/s for the entire trip
Determine the angular acceleration of this turntablr : When the power is turned off on a turntable spinning at 67.0 rpm, you find that it takes 13.0 revolutions for it to stop while slowing down at a uniform rate. What is the angular acceleration (in rad/s^2), of this turntable
Determine the maximum bending stress on the outside surface : A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Spreader beam and hoisted by a crane

The 3.5mg engine is suspended from a 500 kg spreader beam and hoisted by a crane which gives it an acceleration of 4m/s^2 when it has a velocity of 2m/s. determine the force in chains AC and AD during the lift.

  Convert all quantities to si units then convert it to mph

Assume the plane is flying at an altitude of 32,810 ft (10 km), where the temperature is -8 C and the pressure is 250 mb. The Pitot-static tube measures a piezometric pressure difference corresponding to 1.206 psi. What is the airspeed in both m/s..

  Determine the maximum compression of the spring

The 30-Mg freight car A and 15-Mg freight car B are moving toward each other with the velocities VA= 20 km/h to the right and VB= 10 km/h to the left. the spring constant on car A is k= 3MN/m.

  Determine what is the bettle stations impact speed

A separatist Droid Army bettlestation is damaged during an intense battle over Coruscant, and it begins to fall towards to planet with an acceleration of s' = -gR^2/s^2 where s is the bettlestation's distance from Coruscant's center

  When will the queue clear

where u(t) is in vehicles per minute and t is in minutes. When will the queue clear?

  What is the mean velocity of air in the micro-channel

A micro-channel of diameter 0.5 mm and length 750 mm is connected to a plenum. A fan produces a negative gage pressure of -1.5 inch H2O in the plenum and draws air at 20oC into the micro- channel.

  Determine what is the power to use the elbow

An elbow, 90 degrees smooth bend flanged, is used in the Alaskan pipeline. Inside pipe diameter is 48 inches. Flow is 1.6 million barrels a day. 1 barrel=42 gal. Velocity is 8.27 ft/s. SG=0.93

  Determine the compositions and quantities of gas and liquid

Determine the compositions and quantities of gas and liquid when 1 lb mole of a mixture of 30 mole percent methane and 70 mole percent ethanol is brought to equilibrium at 0 F and 500 psia.

  Determine the molar fraction of the gas that condenses

The stream from a gas well is a mixture containing 50 mol % methane, 10 mol % ethane, 20 mol % propane, and 20 mol % n-butane. This stream is fed into a partial conderser maintained at a pressure of 250 psia

  Write computer code using matlab that emoloyes the nelder

write computer code using Matlab that emoloyes the nelder and mead simplex method to solve the welded-beam design (benchmark problem

  Find the force ratio equation

How do you find the force ratio equation to determine the maximum total load that can be applied to a truss?

  Estimate the aqueous concentration of pce in water

Consider tetrachloroethene (PCE) in water. The vapor pressure of PCE is 0.0251atm. Henry's constant for PCE at 25°C is 26.9 atm-L/mol. Estimate the aqueous concentration of PCE in water at equilibrium

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd