User Account

All Pages

Determining the overall heat transfer coefficient

Assignment Help Electrical Engineering
Reference no: EM13879487

A boiler used to generate saturated steam is in the form of an un-finned, cross-flow heat exchanger, with water flowing through the tubes and a high-temperature gas in cross flow over the tubes. The gas, which has a specific heat of 1120 J/kg · K and a mass flow rate of 10 kg/s, enters the heat exchanger at 1400 K. The water, which has a flow rate of 3 kg/s, enters as saturated liquid at 450 K and leaves as saturated vapor at the same temperature. If the overall heat transfer coefficient is 50 W/m2 · K and there are 500 tubes, each of 0.025-m diameters what is the required tube length? 

Reference no: EM13879487

Questions Cloud

Find input demand function for labor and land constraints : Formulate this problem as an LP model to maximize the profit. Also find the input demand function for labor and land constraints
Free convection across the air space : If the building and storm windows are at 20 and -10oC, respectively, what is the rate of heat loss by free convection across the air space?
Difference between authentication and authorization? : What is the difference between authentication and authorization? Can a system permit authorization without authentication? Why or why not?
Face the accounting department of organizations : What is an important challenge facing the accounting department of organizations today, and how would you go about addressing it? Explain.
Determining the overall heat transfer coefficient : The water, which has a flow rate of 3 kg/s, enters as saturated liquid at 450 K and leaves as saturated vapor at the same temperature. If the overall heat transfer coefficient is 50 W/m2 · K and there are 500 tubes, each of 0.025-m diameters what ..
What is an information security program? : What is an information security program?
Describe the message the soldier poet tries to convey : Explain whether you think poems like these would be successful or popular today. What might be a better way to describe modern war: blogs? videos? websites?
Estimate the condensation rate assuming : A beverage can with a diameter of 65 mm and a height of 120 mm has a uniform temperature of 5°C when it is removed from the refrigerator. The can is set on a table in a room with an ambient air temperature of 32°C and a relative humidity of 75%. E..
What is information security policy? : What is information security policy? Why it is critical to the success of the information security program

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the real-reactive and apparent power delivered

(1) a lighting load drawing 10kW, (2) an induction motor drawing 10 kVA at 0.9 power factor lagging, and (3) a synchronous motor operating at 10 hp, 85% efficiency and 0.95 power factor leading (1 hp = 0.746 kW). Determine the real, reactive, and ..

  Define a sinusoidal voltage has a maximum value

A sinusoidal voltage has a maximum value of 100V, and the value is 10V at t=0. The period is T=1ms. Determine v(t)

  Assume both antennas are ideal.

Assume both antennas are ideal.

  Operating open-delta

Three 25.0KVA, 4801120VAC, single-phase, 60Hz transformers are connected delt-delta. The load on the bank is 50.0KVA, balanced load, with power factor of 1.0. A fault in one transformer required its removal, and the bank is operating open-delta. D..

  What is maximum horizontal motion of the work-piece motion

The work-piece motion of a certain system is measured using an LVDT that outputs 12mV/cm. (i) If the output from the LVDT ranges from -12mV to 24mV, what is the maximum horizontal motion of the work-piece motion

  Display a message that the value was not in the array

First, generate an array of 20 input random integers in the range between 0 to 30 and display. Then, sort the generated 20 random integer numbers in ascending order using "THE SELECTION SORT" method and display your sorted output data flow chart.

  Find the value of the field current and the value of r

The DC machine rotates at 1500 RPM and it delivers rated current at rated terminal voltage. The field winding is connected to a 120 V supply. Find the value of the field current and the value of R (field control resistance) required.

  Design rc low-pass filter to attenuate sinusoidal voltage

Using a 500 Ohm resistance, design an RC low-pass filter that would attenuate a 120-Hz sinusoidal voltage by 20 dB with respect to the DC gain.

  How to analyze electric circuit

How to Analyze Electric Circuit through Norton's Theorem ? ( Need an easy step by step procedure with examples )

  Introin this design you are going to use a chain of

introin this design you are going to use a chain of flip-flop to implement a shifter register.design requirementwhen

  Derive the step response and voltage transfer function

Design an active first-order RC low-pass filter (using a 741 op-amp) with a cut-off frequency of 10 kHz and a band-pass gain of 20 dB. Derive the step response and voltage transfer function.

  Find the error for a 1 degree c change in temperature

A pressure measurement system is stated as having the following characteristics. Range: 0 to 140 kPa; Accuracy: ±1.5% of the displayed reading; Temperature sensitivity: ±0.1% of the reading per °C If the instrument indicates a pressure of 120 kPa

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd