User Account

All Pages

Determining the maximum allowable power

Assignment Help Mechanical Engineering
Reference no: EM13880060

A square (10 mm x 10 mm) silicon chip is insulated on one side and cooled on the opposite side by atmospheric air in parallel flow at U8 = 20 m/s and T8 = 24°C. When in use, electrical power dissipation within the chip maintains a uniform heat flux at the cooled surface. If the chip temperature may not exceed 80°C at any point on its surface, what is the maximum allowable power? What is the maximum allowable power if the chip is flush mounted in a substrate that provides for an unheated starting length of 20 mm? 

Reference no: EM13880060

Questions Cloud

Explain the crime bertha committed : Discuss whether Bertha committed a crime and outline the elements of criminal law the prosecutor would use to determine a crime was committed. Explain the crime Bertha committed. Use the elements of criminal law to substantiate your ideas
Valuation of declining growth stock : Martell Mining Company's ore reserves are being depleted, so its sales are falling. Also, because its pit is getting deeper each year, its costs are rising. As a result, the company's earnings and dividends are declining at the constant rate of 7% pe..
Distinguish among the focuses of the gaas standards : Distinguish among the focuses of the GAAS standards of fieldwork and standards of reporting.
About the effective interest rate : On January 2013, Professor Lee buys a house. Here is the information. What is the effective interest rate? If from January 2013, Professor Lee plans to sell his house after 15 years. What is the effective interest rate for Professor Lee in Jan 2013?
Determining the maximum allowable power : What is the maximum allowable power if the chip is flush mounted in a substrate that provides for an unheated starting length of 20 mm?
Explain who is most likely to engage in this act : Explain how this attack was most likely orchestrated. Explain who is most likely to engage in this act, that is, whose habits and limitations are clearly suited to such conduct and why
Explain how an audit trail might get lost : Explain how an audit trail might get lost within a computerized system.
What was lance murdocks rate of return : If you are offered $340,000 in 15 years and you can earn 13 percent on your money, what is the present value of $340,000? Lance Murdock purchased a wooden statue of a Conquistador for $7,500 to put in his home office 6 years ago. Lance has recently m..
Describe the three causes of information risk : Describe the three causes of information risk.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Use work and energy principle to find velocity

A spring stiffness k= 500 n/m is mounted against a 10 kg block. if the block is subjected to a force of 1 KN determine the velocity of the block at s=0.3 m when s=0, the block is at rest and the spring is uncompressed. The coefficient of fricktion is..

  The specific internal energy in kjkg at the initial state

20 kg of water at 200 kpa with a quality 25 is heated under a constant volume process until its pressure reaches 400

  Determine the fluid gage pressure

The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift cars up to 2000 kg. Determine the fluid gage pressure that must be maintained in the reservoir.

  Finally compressed at the constant pressure to the initial

a piston-cylinder device contains 0.15kg of air initially at 2mpa and 350oc. the air is first expanded isothermally to

  Calculate the rate of change of heat with the cylinder

how do i calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall.

  A rigid tank having a volume of 01 m3 initially contains

a rigid tank having a volume of 0.1 m3 initially contains water as a two-phase liquid-vapor mixture at 1 bar and a

  Assuming the following component efficiencies and isa

a simple turbojet is operating with a compressor pressure ratio of 8.0 a turbine inlet temperature of 1200 k and a mass

  For each sketch keep the direction vector within one unit

for a crystal with a cubic structure sketch its unit cells showing the following crystallographic directionsa 011 b 212

  Carbon monoxide at 77f 1 atm enters and insulated reactor

carbon monoxide at 77f 1 atm enters and insulated reactor operating at steady state and burns with air entering at 77 f

  Nitrogen n2 initially occupying 01 m3 at 6 bar 2478c

nitrogen n2 initially occupying 0.1 m3 at 6 bar 2478c undergoes an internally reversible expansion during which pv 1.20

  Given a rectangular sample of ductile iron 60-40-18 with

given a rectangular sample of ductile iron 60-40-18 with cross sectional dimensions 0.8 in x4 in calculate the stress

  What is the number of moles of the helium gas

A balloon is inflated with helium gas to a pressure of 100 kPa gauge. The volume of the balloon is 0.4m^3. The initial temp is 20 degrees C. The helium gas can be treated as an ideal gas. the atmospheric pressure is 101.3 kPa

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd