Determining the approximate water temperature

Assignment Help Mechanical Engineering
Reference no: EM13946599

Water flows at a velocity uoo = 1 m/s over a flat plate of length = 0.6 m. Consider two cases, one for which the water temperature is approximately 300 K and the other for an approximate water temperature of 350 K. In the laminar and turbulent regions, experimental measurements show that the local convection coefficients are well described by

hlam(x) = Clam x-0.5        hturb(x) = Cturb x-0.2

where has units of m. At 300 K,

Clam,300 = 395 W/m1.5 · K          Cturb,300 = 2330 W/m1.8 · K

while at 350 K,

Clam,350 = 477 W/m1.5 · K          Cturb,350 = 3600 W/m1.8 · K

As is evident, the constant depends on the nature of the flow as well as the water temper- ature because of the thermal dependence of various properties of the fluid.

Determine the average convection coefficient, h, over the entire plate for the two water temperatures.

Reference no: EM13946599

Questions Cloud

Harris corporation produces a single product : Harris Corporation produces a single product
Temperature and heat flux measurements : What are the molar concentration and the species molar flux of the water vapor at a location (x*, y*) corresponding to the point at which the temperature and heat flux measurements were made in the first case?
Creating new information technology systems for a company : Communication - key; the more they know, the less likely there will be opposition or opposition will be mitigated; email, reports, meetings
Find the height to which the water can be delivered : Find the height to which the water can be delivered - A centrifugal pump delivers water at the rate of 0.22 m3/s from a reservoir at ground level toanother reservoir at a height H, through a vertical pipe of 0.2m diameter.
Determining the approximate water temperature : Water flows at a velocity uoo = 1 m/s over a flat plate of length L = 0.6 m. Consider two cases, one for which the water temperature is approximately 300 K and the other for an approximate water temperature of 350 K. In the laminar and turbulent r..
Metallurgical engineer : A metallurgical engineer decides to set aside money for his newborn daughter's college education.
Famed boston rock and roll club euphoria : On May 1, 1995, the famed Boston rock and roll club Euphoria burned to the ground. Luckily, the fire began at 2:00 a.m. and no one was injured. The highly anticipated and sold out May 2, 1995, concert of the New York rock group Zephyr was cancelle..
Results for the local heat transfer coefficient : Experimental results for the local heat transfer coefficient hx for flow over a flat plate with an extremely rough surface were found to fit the relation
Which has access to the raw message : Please answer this post like discussion if you agree or disagree, and why? Please explain it. This post is the answer from somebody else about question

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the temperature at the exit of the turbine

Air enters a 3600-kW turbine operating at steady state with a mass flow rate of 18 kg/s at 800oC, 3 bar and a velocity of 100 m/s. The air expands adiabatically through the turbine and exits at a velocity of 150 m/s.

  Ideal gas equation and van der waals equation

A rigid tank has a volume of 23.3 m3 and due to safety requirements its pressure should not exceed 105 bar. If the tank has been filled with 1000kg of water vapor and is heated to 360°C check to see if it is within safety requirements.

  The second shaft is hollow with an outside diameter of 3 in

two steel shafts are made of cold-drawn steels having ultimate tensile strengths of 185 kpsi and 240 kpsi respectively.

  Calculate the uncertainty in the dimensional measurement

A pneumatic displacement gage has d1=0.762 mm and d2=1.575 mm. The supply pressure is 68919.7 Pa with a random fluctuation of ±483 Pa, and the differential pressure Pd-Pa is measured with a water manometer that may be read with an uncertainty of 12.4..

  Find the reheat temperature so the turbine output is

a smaller power plant produces steam at 3 mpa 600 c in the boiler. it keeps the condenser at 45 c by transfer of 10 mw

  Use potential flow theory to determine the lift coefficient

use potential flow theory to determine the lift coefficient of a spinning baseball in terms of the forward velocity v

  Rankine cycle with a single open feed water heater

Consider an ideal Rankine cycle with a single open feed water heater. The boiler pressure is 800 psia, and the condenser pressure is 2 psia. Steam is extracted from the turbine to heat the feed water at 90 psia. Steam enters the turbine at 1000F.

  An escalator brings four people of total 300 kg 25 m up in

an escalator brings four people of total 300 kg 25 m up in a building. explain what happens with respect to energy

  Determine a the mass flow rate through the nozzle b the

air enters an adiabatic nozzle steadily at 300 kpa 200 degree cesius and 30 ms and leaves at 100 kpa and 180 ms. the

  Rake angle15degree cutting force500n and thrust force200n

an orthogonal cutting operation is being carried out under the following conditions depth of cut 0.15mm width of cut5mm

  Determine exit temp of oil and heat transfer rate between

consider a shell and tube heat exchanger which is used to heat water cp water 4.33kjkgk from 10 deg c to 85 deg c

  Design value of the overall convection coefficient

A counter flow, concentric tube heat exchanger used for engine cooling has been in service for an extended period of time. The heat transfer surface area of the exchanger is 5 m2, and the design value of the overall convection coefficient is 38 W/..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd