Determine which tunnel allows more modes to propagate

Assignment Help Electrical Engineering
Reference no: EM13274635

A recent study has been carried out concerning radio propagation in railway tunnels. In this study, two railway tunnels of rectangular cross section are considered. Tunnel 1 has transverse dimensions of width a = 8 m and height b = 4 m, and tunnel 2 has the same height but a narrower width, a = 6 m. Assuming the tunnels to be empty with perfectly conducting walls, find the total number of propagation modes possible in each tunnel at 100 MHz. Which tunnel allows more modes to propagate?

Reference no: EM13274635

Questions Cloud

Explain the pros and cons of debt financing : Explain the pros and cons of debt financing (borrowing) and equity financing (issuing stock). Examine the balance sheets of a few companies and determine what percentages they are financed through debt and equity. In today's economic climate wh..
Calculate the speed of the particle : The speed of a particle moving in a circle 2.0 m in radius increases at the constant rate of 4.4 m/s2. what is the speed of the particle
Determine the required wave impedance of the section : To avoid reflections, an X-band waveguide section λg/4 in length is inserted between the two. Assume dominant mode propagation and that the match is at 10 GHz. a) Determine the required wave impedance of the λg/4 section
Dambro''s available-for-sale portfolio : On August 1, 2014, Dambro Company acquired 800, $1,000, 9% bonds at 97 plus accrued interest. The  bonds were dated May 1, 2014, and mature on April 30, 2020, with interest paid each October 31 and  April 30. The bonds will be added to Dambro's av..
Determine which tunnel allows more modes to propagate : A recent study has been carried out concerning radio propagation in railway tunnels. In this study, two railway tunnels of rectangular cross section are considered. Tunnel 1 has transverse dimensions of width a = 8 m
Calculate the angle through which the electron scatters : In a Compton scattering experiment, an x-ray photon scatters through an angle of 18.0° from a free electron that is initially at rest. Calculate the angle through which the electron scatters
Explain electophilic addition reaction of conjugated dienes : The electophilic addition reaction of conjugated dienes that occurs at low temperatures and/or short reaction times is said to be under what? A)thermodynamic control B)kinetic control C)1,2-additon control D) 1,4-addition control
Design an air-filled c-band rectangular waveguide : Design an air-filled C-band (5-8 GHz) rectangular waveguide such that the center frequency of this band (f= 6 GHz) is at least 25% higher than the cutoff frequency of the TE10 mode and at least 25% lower than the cutoff frequency of the next highe..
How much energy does this device transfer into hot reservoir : A device uses a Stirling cycle on 433 moles of a monatomic ideal gas between two reservoirs with temperatures of 416 K, How much energy does this device transfer into the hot reservoir

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design appropriate amplifier needed to maintain the signal

the hd cable signal send out is usually ranging between (1-25mv), with the frequency range from 1000Hz- 20Khz. An amplifier will gain 46 db will boost the signal before sending it through the cable connection.

  Determine the total current in each line of 3-phase motor

Three -phase motor is connected to a three-phase power source that has an abc phase sequence. the first load is a wye-connected, three-phase motor withdrawing a line current of 20A at a 0.8 lagging power factor.

  Find the mean of the random process x

Let the random process X(t) be defined as X(t) = A + Bt, where A and B are independent random variables each uniformly distributed in [-1, 1]. a) Find the mean of X(t). b) Find Rx(t1, t2) c) Is X(t) wide-sense stationary

  Draw a band diagram

Calculate the Fermi level position relative to conduction band (Ec-Ef) and relative to valence band (Ef-Ev).

  Design a low-pass filter that attenuates the noise

A measurement signal has a frequency less than 1 kHz, but there is unwanted noise at about 1 MHz. Design a low-pass filter that attenuates the noise to 1%. What is the effect on the measurement signal at its maximum of 1 kHz

  How much coal did we burn

The residential sector of PA consumed about 150.6x1012 Btu of electricity (www.eia.doe.gov). Assuming all of this energy comes from bituminous coal with a heating value of 14,000 Btu/lb. How MUCH coal did we burn?

  Explain briefly why a capacitor can block dc voltage

Explain briefly why a capacitor can block DC voltage. How might you use this feature in a design. Explain why the impedance Zeq of a parallel RC circuit decreases as the frequency increases.

  Find how many numbers are above the average

1- Write a function that shows you how to calculate F(x) = 0.1X^2+5Y^3 2- Read and write a File that has a set of 10 numbers. Then assign those numbers to an array.

  Why boundary conditions are so important in electromagnetics

1. Derive boundary conditions for electric fields (both for tangential and normal components) 2. Derive boundary conditions for magnetic fields (both for tangential and normal components) 3. Why boundary conditions are so important in electromagnetic..

  Why has lead-free solder replaced lead-based solder

1. What is the purpose of core in hollow solder wire 2. What is tinning, and why is it important 3. Why is safety so important when soldering 4. Why has lead-free solder replaced lead-based solder. Be sure to properly cite any sources of information.

  Find the load impedance in per unit to be used in impedance

One side of the transformer bank is connected to a 120-kV transmission line, and the other side is connected to a three-phase load of 10 MVA at 13.2kV and 0.8 lagging power factor. Using the base in the tranmission line of 120-kV and 20 MVA.

  Find relation for the potential across the depletion region

Consider a linearly graded Si p-n junction. Find a relation for the potential across the depletion region. Hint: Start from equation 29 in chapter 3 of the text book. Integrate the electric field to find the potential.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd