Determine which output signal suers the worst delay

Assignment Help Electrical Engineering
Reference no: EM13282506

A binary adder takes in two 24bit 2's complement binary numbers, plus a carry-in signal, and produces a 24 bitresult, a carry-out signal and an overow signal. If Nand gates are used throughoutand a ripple-carry design is used, calculate the delay through the adder, assuming all inputs are presented at the same instant, and counting D seconds per gate. Which output signal suers the worst delay (including the carry-out and over ow outputs)?

Reference no: EM13282506

Questions Cloud

Determine the final sound wave amplitudes : Suppose that the sound level of a conversation is initially at an angry 70 dB and then drops to a soothing 50 dB. determine the final sound wave amplitudes
Issue relevant to young children and play : Students will write a 5-8 page research review of an issue relevant to young children and play, using at least 5 professional research journal resources
Find the density as a function of height : In a non-uniform gas, the equation of state is valid locally, as long as the density does not change too rapidly with position. Find the density as a function of height
Heat is needed to raise the temperature of a mole of oxygen : How much heat is required to raise the temperature of a mole of oxygen from 298 to 3000 K at constant pressure
Determine which output signal suers the worst delay : If Nand gates are used throughoutand a ripple-carry design is used, calculate the delay through the adder, assuming all inputs are presented at the same instant, and counting D seconds per gate. Which output signal suers the worst delay.
Regression analysis- benefits and intrinsic : Run a regression analysis using the BENEFITS column of all data points in the AIU data set as the independent variable and the INTRINSIC job satisfaction column of all data points in the AIU data set as the dependent variable.
Compute the standard molar enthalpy of formation : Calculate the standard molar enthalpy of formation ?H°f of N2H4(g) from the following information: N2(g) + 2H2(g) ? N2H4(l) ?H°rxn = +50.6 kJ N2H4(g) ? N2H4(l) ?H°rxn = -44.8 kJ A. +5.8 kJ/mol B. +95.4 kJ/mol C. +47.7 kJ/mol D. -95.4 kJ/mol E. -5...
Determine the focal length of the projection lens : How far from the object should the lens of the projector be placed to form the image on the screen?
What is the net cash flow from the salvage value : Ronnie has been offered $52,000 for his old assets. What is the net cash flow from the salvage value if the tax rate is 34 percent?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the poles in frequency response at node a

An AC model of a cascode common-source amplifier is shown below. M1 and M2 are biased in saturation mode. The parasitic capacitors in the transistors are included. Determine the poles in frequency response at node A, X, and Y respectively.

  Find the zener voltage at a current

a 9.1 v zener diode exhibits its nominal voltage at a test current of 28 mA . at this current the incremental resistance is specified as 5 ohms . find Vz0 of the zener model . find the zener voltage at a current of 10 mA and at 100 mA.

  What is the minimum and maximum number of states

Suppose you are told that a Moore machine has five flip flops, three inputs and nine outputs. What is the minimum and maximum number of states in the state diagram, the minimum and maximum number of transition arrows at a particular state

  Design a synchronous sequential circuit with one input line

Design a synchronous sequential circuit with one input line and one output line that recognizes the input string x = 1111. The circuit is also required to recognize overlapping sequence such that if the input string is x = 1101111111010

  What is the bridge output per hour stress

A Whetstone bridge has a strain gage in the lower right leg with a 120 ohm nominal resistance. It is mounted on steel with a Modulus of Elasticity equal to 30x106. The other resistors are equal to 120 ohms.

  Find real part of the network is a series rlc

Consider a network with a driving-impedance Z. (1) Find expression for P and Q. (2) Find p(t) in terms of P and Q. (3) Suppose that the network is a series RLC. Interpret the result in part (2).

  Find the energy absorbed by the element in seconds

the voltage across an element is 12e^-2t V. the current entering the positive terminal of the element is 2e^-2t A. Find the energy absorbed by the element in 1.5 seconds starting from t =0.

  What is the inductance of the toroidal maganitic core

a toroidal maganitic core is wrapped with a coil of wire containing 200 turns. the cross sectional area of the core is 10 cmsq,and the mean length around the core is 20 cm. the material permability is 0.001 hy/m. what is the inductance of the devi..

  Describe quantitatively how would vout vs frequency

A Bandpass Filter, made up of a High pass RC circuit to a Low Pass RC circuit has values of R1=R2=10.0 kohm and C1=C2=0.01uF is created. Varying the driving frequency from 10Hz to 1MHz in decades and measure Vout and the phase angle.

  Determine the maximum raw instantaneous data

Determine the maximum raw instantaneous data rate that can be provided to a single user in EDGE, assuming that a single time slot on a single GSM channel is available.

  What is the voltage drop on a feeder 450 ft long

What is the voltage drop on a feeder 450 ft long 4 uncoated copper wire in steel conduit. V=480 3 phase four wire 60 hz. 64 amps .85 pf.

  Determine free electron and hole concentration

(a) Determine free electron and hole concentration.(b) Calculate the effective density of states at valence band, Nv. Given that ni = 1x1010 cm3 and kT = 0.026.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd