Determine whether condensation occurs

Assignment Help Mechanical Engineering
Reference no: EM131147904

Chilled air at 15?C enters a horizontal duct at a speed of 1 m/s. The duct is made of thin galvanized steel and is not insulated. A 30 m section of the duct runs outdoors through humid air at 30?C. Condensation of moisture on the outside of the duct is undesirable, but it will occur if the duct wall is at or below the dew point temperature of 20?C. For this problem, assume that condensation rates are so low that their thermal effects can be ignored.

a. Suppose that the duct's square cross-section is 0.3 m by 0.3 m and the effective outside heat transfer coefficient is 5 W/m2K in still air. Determine whether condensation occurs.

b. The single duct is replaced by four circular horizontal ducts, each 0.17 m in diameter. The ducts are parallel to one another in a vertical plane with a center-to-center separation of 0.5 m. Each duct is wrapped with a layer of fiberglass insulation 6 cm thick (ki = 0.04 W/m·K) and carries air at the same inlet temperature and speed as before. If a 15 m/s wind blows perpendicular to the plane of the circular ducts, find the bulk temperature of the air exiting the ducts

Reference no: EM131147904

Questions Cloud

Determine how to do payroll for the merged company : It was your job to pull these team members together, to determine how to do payroll for the merged company with less staff, and therefore to reduce costs.  And you succeeded
Project finance and procurement : Griffith University one of the most prestigious universities in the country plans for starting of high quality student accommodation centre. It is in the planning stage and is being planned for with quite of lot of amenities included such as 300 bay ..
Derive a formula for the time to empty the tank : A swimming pool W by Y by h deep is to be emptied by gravity through the long pipe shown in Fig. P6.54. Assuming an average pipe friction factor fav and neglecting minor losses, derive a formula for the time to empty the tank from an initial level..
Consumer decision-making process : When purchasing products, consumers generally follow the consumer decision-making process. Review this process in your text. Then think of a product you purchased that involved extensive decision making. Name the product and describe your experience ..
Determine whether condensation occurs : Suppose that the duct's square cross-section is 0.3 m by 0.3 m and the effective outside heat transfer coefficient is 5 W/m2K in still air. Determine whether condensation occurs.
Power consumption has risen from the usual level : You are a quality manager. On one of your company’s product lines, a report shows that power consumption has risen from the usual level of 35.5 W to a level of 35.9 W. This difference is, without a doubt, statistically significant. However, the line ..
Determine how many shares you can buy : Indicate the number of shares you are buying, and the price of the shares you are buying for each company: Once you decide the companies and the amount for each company, determine how many shares you can buy.
About the beer map and shampoo map : For (1( beer and (2) shampoo products that you are familiar with, develop positioning (perceptual) maps that reflect your knowledge of paticular products in these categories. Include for products in both your beer map and shampoo map. Below each map ..
What is the maximum roof area that can be drained : The gutter is designed for a sudden rainstorm of up to 5 inches per hour. For this condition, what is the maximum roof area that can be drained successfully?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd