Determine what pressure must be provided at point 1

Assignment Help Civil Engineering
Reference no: EM13321050

From a point 1, a 25mm diameter pipe runs horizontally under the floor and then a 12.5 mm diameter line runs 1 m up the wall to a point 2. To maintain a pressure of 300kPa at point 2, what the 15 C water is flowing at 0.5 L/s, what pressure must be provided at point 1 if you neglect friction?

Reference no: EM13321050

Questions Cloud

Find the steady-state concentration to be completely mixed : Suppose an air pollutant with rate constant k= 0.20/hr is emitted into the box at a total rate of 10.0 kg/s. Find the steady-state concentration if the air is assumed to be completely mixed.
Estimate the work done on the gas : In a certain experiment, the pressure of a gas depends on the volume by P=alphaV^3+betaV^2, What is the work done on the gas
Explain molecular formula of the compound : What are the empirical formula and the molecular formula of the compound.
Analysis of business needs and requirements : Analysis of Business Needs and Requirements.
Determine what pressure must be provided at point 1 : To maintain a pressure of 300kPa at point 2, what the 15 C water is flowing at 0.5 L/s, what pressure must be provided at point 1 if you neglect friction
Compute the specific weight and specific gravity of the oil : A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Determine the freezing point of water : The Ed-Scale defines the perfect temperature of a martini to be 14 degrees E and the boiling point of antifreeze to be 100 degrees E. Use this equation to find the freezing point of water in Eds
What is the min possible value for the pressure difference : Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs).
Find the linear mass density of the cord : Suppose the tension in a cord is 12.0 N. If the speed of a wave in the cord is 9.50 m/s, then what must be the linear mass density of the cord

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the percentage increase in the discharge the ditch

As part of a drainage improvement project, a drainage ditch will be straightened and cleaned. As a result, the lenght of the ditch will decrease from 1800 ft to 1400 ft and the mannings roughness factor will be reduced to 0.018 from 0.022.

  Design the weir structure in order to accommodate the design

The channel cross section is rectangular in shape,with a bed width of 4 m and Manning n of 0.022. The bed drops by an average of 4.2metres every kilometre. The maximum flow in the channel is equal to 7 m3/s.

  How much distance must be cleared from the center of lane

If the superelevation is .10 at the station of the PC is 17+35, what is the station of the PI and how much distance must be cleared from the center of the lane to provide adequate stopping sight distance

  Question in structure analysis

Determine axial force and Max bending - Question in structure analysis

  Determine the maximum allowable value of p

The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in.

  What measurements should be laid out to establish a distance

a tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. what measurements should be laid out to establish a horizontal distance of 682.25ft

  What is the steady-state concentration of salt in the tank

A two thousand gallon tank has two influent streams. Influent one has a flow of 20 GPH and a salt concentration of 100 mM; influent two has a glow of 15 GPH and a salt concentration of 200 mM. What is the steady-state concentration of salt in the ..

  Identify each corner by a suitable description on the sketch

Make a sketch indicating the incorrect and correct positions of such an original section corner and also the positions of the adjacent corners used in relocating that corner

  Determine the oxygen concentration below the dam

A flat broad-crested regular step dam with a drop of 2 m is situated on a grossly polluted stretch of river below a sewage outfall plant. The river is located at an elevation of 2 km.

  Construct an uniform thick deposit of cohesionless soil

A proposed square footing carrying a total load of 900 kips is to be constructed on a uniform thick deposit of cohesionless soil. The soil's unit weight is 135 pcf, and its angle of internal friction is 38 degrees

  Position of the race car when acceleration is given

Starting from x = 0 with no initial velocity, the acceleration of a race car is defined by the relation a = 6.8e- 0.00057x , where a and x are expressed in m/s 2 and meters, respectively. Determine the position of the race car when v = 30 m/s.

  Determine what is the coefficient of permeability

An aquifer is 45 meters deep and has a well that pumps water at 850 cubic meters per day. One observation well is located 45 meters away and has a water surface that is 44.35 meters above the bottom of the aquifer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd