Determine what manometer reading can be expected

Assignment Help Civil Engineering
Reference no: EM13307578

A flowrate of 1.0 L/min of oil of specific gravity 0.92 exists in this pipeline. Is this flow laminar? What is the viscosity of the oil? For the same flow in the opposite directio, what manometer reading can be expected?

Reference no: EM13307578

Questions Cloud

What wavelength of light is transmitted into the water : After a hard rain, you walk out into the parking lot and notice an oil sheen on top of a puddle of water. when viewed from directly above, What wavelength of light is transmitted into the water
What is the diameter of the flow tube of water : A continuous stream of water runs from the faucet into a kitchen sink, picking up speed as it falls. What is the diameter of the flow tube of water
Write a java program that declares an array alpha : Initialize the array so that the first 25 elements of array are equal to the square of the index variable, and the last 25 elements are equal to three times the index variable. Output the array so that 10 elements per line are printed on the conso..
What is force necessary to pull the loop : A loop of width 0.2m and length 0.8m, and resistance 200ohms is pulled through a magnetic field of 0.4 T at 0.2 m/sec. What is force necessary to pull the loop
Determine what manometer reading can be expected : Is this flow laminar. What is the viscosity of the oil. For the same flow in the opposite directio, what manometer reading can be expected.
How will this policy-change affect outpatient care market : How will this policy-change affect outpatient care market and what will be effect of this hospital admission reviews on the insurance market?
Implement the class with accessors and mutators : Implement the class with accessors and mutators for the movie name and MPAA rating. Write a method addRating that takes an integer as an input parameter.
What is the speed of the other train : Two trains are moving in opposite directions on parallel tracks and are approaching a station. What is the speed of the other train if an observer at the station hears a beat frequency of 4.4Hz
Write an xeyes command to display a window : Find and install xeyes (not tuxeyes). Write an xeyes command to display a window that is 600 pixels wide and 400 pixels tall, is located 200 pixels from the right edge of the screen and 300 pixels from the top of the screen.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate stress along edge a-b caused by prestressing force

A horizontal pre-stressing force of 750kn is applied to a rectangular concrete beam to be used as a structural member of a traffic bridge. The beam has a depth of 500mm and a width of 250mm. The force is applied at a distance of 80mm below the sec..

  Determining stress fort rigid bar of negligible weight

The rigid bar of negligible weight is supported as shown. Find the stress in each rod if the temperature rises DeltaT after a load P is applied. Use the following data: area of steal rod 320mm2, bronze rod 1300mm2, thermal expansion coefficient Al..

  Estimate the direct runoff in inches for a design storm

Of this total, 2000 acres are residential(CN=68), 500 acres are industrial (CN=88), and 2500 acres are forest with good cover (CN=55). For a design storm of with a total precipitation of 7 inches, estimate the direct runoff in inches.

  Find what pressure gradient is required to accelerate water

What pressure gradient is required to accelerate water vertically upward in a vertical pipe at a rate of 0.5g

  Determine the average normal stress and average shear stress

A wood board with a 2in. by 4in. cross section is subjected to a tensile load of 100 lb. Determine the average normal stress and average shear stress developed in the wood fibers that are oriented at 30 degrees with the axis of the board.

  Determine what is the design speed of the curve

An equal tangent vertical curve connects a -2% and a +3% grade. The low point of the curve is at elevation 297.88 ft. If the PVI is at elevation 295 ft, what is the design speed of the curve

  Percent elongation and percent reduction in area

Also, at the failure cross sections the diameters are found to be 0.731 in., 0.645 in., and 0.587 in., respectively. Determine the percent elongation and percent reduction in area of each specimen.

  What is the draft h of the barge when floating in sea water

A barge has the trapeziodal shape and is 22 m long into the paper. If the total weight of barge and cargo is 350 tons, what is the draft H of the barge when floating in sea water

  Determine what is the resultant thermal energy

The specific heat (C sub p) of aluminum is 0.214 calories per gram degrees Celsius (0.214 cal/g-C). If a cube of aluminum with a mass of 13.6 kg exhibits a change in temperature of +30 degrees Celsuis, what is the resultant thermal energy

  Drawing the shearing force diagram

Draw the shearing force diagram and the moment diagram of the following problem. The beam is indeterminate. You need to integrate the moment twice to get a formula for the deflection v(x).

  Determine ft and fn

for this purpose replace this force by its equivalent of two forces at At Ft parallel and Fn perpendicular to the beam. Determine Ft and Fn.

  Determine the distance traveled by the cart comes to rest

The system is released from rest with no slack in the cable and the spring stretched 120 mm. The coefficient of kinetic friction between the 10 kg cart is 0.25 and the mass of block m is 6.3 kg.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd