Determine what is the total elongation of the pipe

Assignment Help Civil Engineering
Reference no: EM13296821

a prismatic bar AB of length L, cross section A, modulus of elasticity E, and weight W hangs vertical under its own weight.

if the bar is a riser pipe hanging from a drill rig at sea, what is the total elongation of the pipe? let L=150m, A=0.0157 m^2, and E=210GPa

Reference no: EM13296821

Questions Cloud

Which car had the greater velocity before the collision : Two cars of equal mass collide at right angles to each other in an intersection. Which car had the greater velocity before the collision
How fast could the insect be moving : A visual inspection of an insect with mass 0.4mg (milligrams) suggest that its uncertainty in postion is 0.5um, How fast could the insect be moving
Explain order of decreasing net dipole moment : Which of the following pairs of molecules is listed in order of decreasing net dipole moment (from more polar molecule to less polar molecule)
At what temperature change delta t does the wire go slack : a brass wire of diameter d=1/6 in is stretched between rigid supports with an initial tension T of 37lb. assume the coefficient of thermal expansion is 10.6X10^-6 / F and the modulus of elasticity is 15X10^6 psi.
Determine what is the total elongation of the pipe : a prismatic bar AB of length L, cross section A, modulus of elasticity E, and weight W hangs vertical under its own weight. if the bar is a riser pipe hanging from a drill rig at sea, what is the total elongation of the pipe
Determine what is the max length of the slotted region : a rectangular bar of length l has a slot in the middle half of its length. the bar has width b, thickness t, and modulus of elasticity E. the slot has a width b/4. the stress in the middle region is 24000 psi, the length is 30 in, andthe modulus o..
Define the following balanced chemical equation : Given the following balanced chemical equation, if 345 g of I2 are formed, how many g of Cl2 had to react? 2 FeI2 + 3 Cl2 ? 2 FeCl3 + 2 I2
Determine what is the maximum water hammer pressure : 0.5 m-diameter concrete pipe (5.0 cm rigid wall thickness with rigid pipe walls) carries water 600m before discharging into another reservoir. The surface elevation of the downstream reservoir is 55 m lower than the supply reservoir.
Determine the area of the image : To the left of the lens is a cube having a face area of 100 cm2. Determine the area of the image

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the resistance coefficient k for a ball-type

Calculate the resistance coefficient K for a ball-type check valve placed in a 2-in schedule 40 steel pipe carrying 650 gal/min of oil (sg = 0.90)

  Determine the horizontal reaction

a gate having cross section shown in fig closes an opening 5 ft and 4 ft high in a water reservoir. The gate weighs 400lb and its center of gravity is 1 ft to the left of AC and 2 ft above BC. Determine the horizontal reaction that is developed on..

  Explain lift charts in direct marketing

Lift Charts in direct marketing, The mass-mailing business is often used to illustrate the use of lift charts. Another real world application where the lift charts can be used

  Question in structure analysis

Determine axial force and Max bending - Question in structure analysis

  Find the minimum flow rate of air

Find the minimum flow rate of air and the heat exchanger second-law efficiency.

  Load that a boat can carry without sinking in a lake

The hull of a boat has a volme of 150m and the total mass of the boat when empty is 8560kg. determine how much load this boat can carry without sinking in a lake.

  Four-lane highway for adequate ssd

A horizontal curve was designed for a four-lane highway for adequate SSD. Lane widths are 12 feet, and the superelevation is 0.06 and was set assuming maximum fx.

  Determine the velocity v2 of the particle

The motion occurs in the horizontal x-y plane. Determine the velocity V2 of the particle at the end of the 3-s interval.

  Find dry unit weight of the sample and water content

An undisturbed soil sample was collected in a sampling tube of internal diameter 5cm. The length of the extracted sample was 10.2 cm and its mass was 360 g. After oven drying the mass reduced to 326.5 g.

  Why is the time value of money important

Why is the ‘time value of money' important for the evaluation of engineering projects? Provide at least one practical example to support your view (max 2 pages)

  Find the gauge pressure at a second point in the line

At one point in a pipeline, the water's speed is 3.00 m/s and the gauge pressure is 4.00×10^4 Pa. Find the gauge pressure at a second point in the line 11.0 m lower than the first if the pipe diameter at the second point is twice that at the first..

  What is the axial force in member hj

The frame shown is used to support high-tension wires. If W = 200 lb, b = 3 ft, a = 30°, what is the axial force in member HJ?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd