User Account

All Pages

Determine what is the slew rate of the op amp

Assignment Help Electrical Engineering
Reference no: EM13278776

the input voltage to an op amp is a large voltage step. the output is a exponential waveform that changes 2.0V in 0.4us. what is the slew rate of the op amp.

Reference no: EM13278776

Questions Cloud

What fraction of total energy is potential energy : When the displacement in SHM is 0.2 the amplitude A, what fraction of the total energy is kinetic energy, What fraction of total energy is potential energy
Calculate the return on your short sale transaction : Be sure to factor in any dividends paid on the stock during the four-week period and the interest paid on the borrowed funds. Show your calculations. very important to show the calculation.
What is the output error voltage of differential amp : the diff amp pf has Av= 360 lin(bias)=600nA,lin(off) =100nA and Vin(off)=1mV. what is the output error voltage if a matching base resistor is used, what is the output error voltage
Define how pascals law addresses the pressure in a fluid : Define how Pascal's law addresses the pressure in a fluid at different heights (or depths) before addressing the question and would you apply it in this case
Determine what is the slew rate of the op amp : the input voltage to an op amp is a large voltage step. the output is a exponential waveform that changes 2.0V in 0.4us. what is the slew rate of the op amp.
Price represent to the consumer : What does represent to the marketer? What does price represent to the consumer? Is the dollar figure more than a dollar figure?
Compute how long is the wire : A current of 0.80A flows through a copper wire 0.50mm in diameter, How long is the wire in km
What is the common-mode voltage gain of opamp : a 741C is an op amp with Av= 100000 and a minimum CMRRdB= 70dB. what is the common- mode voltage gain. if a desired and common- model signal each has a value of 5 uV. what is the output voltage.
Explain standard spectrophotometry experiment : Standard Spectrophotometry experiment. I have absorbance, path length (1) and I need to determine the concentration of an unknown based on my calibration cure. I need the Extinction Coefficient. Is that just the slope of by calibration curve? Or i..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate ni and the concentration of electrons

an unknown semiconductor has Eg=1.1ev and Nv=Nc.it is doped with 10^15 donors,where the donor level is 0.2ev below Ec. given that Ef is 0.25ev below Ec, calculate ni and the concentration of electrons and holes in the semiconductor at 300k.

  Determine the photon energies-wavelengths and angle

A positron (same mass as electron) moving at .8c collides head on with a stationary electron producing two photons with EQUAL ANGLES relative to the incoming positron. Find the photon energies, wavelengths and angle

  Find the energy in the conduction band

The electron distribution in the conduction band peaks at energies close to the conduction band edge. Using the Boltzmann approximation, find the energy in the conduction band (as a function of temperature) at which the electron density peaks

  Which protocol successfully delivers all five data segments

Compare GBN, SR, and TCP(no delayed ACK). Assume that the timeout values for all three protocols are sufficiently long such that 5 consecutive data segments and their corresponding ACKs can be received (if not lost in the channel)

  Write a function that takes inputs of quarts and pints

Use appropriate parameter passing and return mechanisms. Use appropriate datatypes. For example, with inputs of 4 quarts and 4 pints, the result would be 1.5 gallons. Use proper code formatting techniques. Do not write a main routine. Your functio..

  Find what is minimum number of gate to implement function

GivenG(A,B,C) =fm (2,3) + d(4,5,6,7) 1. find the Optimum SOP solution 2. What is the minimum number of gate that can be used to implement this function (d represents dont cares).

  Find the inductive and capacitive reactance at resonance

in a RLC series circuit R=500Ω L=0.4mH and C=100pF the circuit is connected to the terminals of an ac source with an rms voltage of 1V, and a variable frequency calculate the following A) resonant frequency

  Explain next generation transmission system

You are required to determine that this next generation transmission system will require a spectral efficiency of 5 bits/sec per Hertz.

  Brief theory on touch voltage

looking for a brief theory on touch voltage, step voltage and ground potential rise (GPR). Should include graphical representation and relevant equations to help in understanding.

  Find the power delivered to the small electric motor

The battery has 2.5 V output voltage and 12 Ohm internal resistance. The battery is used to boot a small electric motor with 145 Ohm resistance. Find the power delivered to the motor.

  Why designer often use signal conditioning amplifier circuit

What are two types of variables that can be used for values that exceed 256, and describe what is the difference between the variables, how to declare them and the memory allocated, and the numerical range for both.

  Design a circuit for a combination lock with one input

Design a circuit for a combination lock with one input, x, and two outputs, unlock and hint. Output unlock should be 1 if and only if x is 0 and the sequence of inputs received on x at the preceding seven clock ticks was 0110111.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd