Determine what is the rate of discharge with rubble masonry

Assignment Help Civil Engineering
Reference no: EM13322286

A 5-m wide rectangular open channel lined with rubble masonry (n=0.025) and laid on a slope of 0.0004. If the depth of flow is 3 m, what is the rate of discharge (m3/s)

Reference no: EM13322286

Questions Cloud

How much charge passes trough the starter motor : The starter motor of a car engine draws a current of 127 A from the battery. How much charge passes trough the starter motor
Find asymptotic solution to following recurrence relations : Using the master methods find the asymptotic solution to the following recurrence relations, specify the case and the asymptotic solution.
Find the potential difference between the end of the wire : The electric field inside a 28.41-cm-long copper wire is 0.021 V/m. What is the potential difference between the end of the wire
Determine what would be the expected flow velocity : A 12-in diameter concrete culvert (n=0.013) flows half full and is constructed on a grade of 0.5 %. What would be the expected flow velocity
Determine what is the rate of discharge with rubble masonry : A 5-m wide rectangular open channel lined with rubble masonry (n=0.025) and laid on a slope of 0.0004. If the depth of flow is 3 m, what is the rate of discharge (m3/s)
Berkshire inc. uses a periodic inventory system : Berkshire Inc. uses a periodic inventory system. At the end of 2012, it missed counting some inventory items, resulting in an inventory understatement by $600,000. Assume that Berkshire has a 30% income tax rate and that this was the only erro..
Write a program that uses a while loop to compute : Write a program that prints the numbers from 1 to 50 using a for loop. Rewrite the program using a do -while loop.
Find range of values of p for which equilibrium is maintain : knowing that the coefficient of static friction between the collar and the rod is .35, determine the range of values of p for which equilibrium is maintained when 0=50deg and M=20Nm
What is the resistance of the composite wire : A 137-cm-long wire is made by welding a 1.3-mm-diameter, 26-cm-long copper wire to a 0.31-mm-diameter, What is the resistance of the composite wire

Reviews

Write a Review

Civil Engineering Questions & Answers

  Explain why not use rubber to seal wine bottles

Cork is used for sealing sparkling wine bottles. Aside from friction, why not use rubberbto seal wine bottles. (Hint: think about the force exerted by the pressure inside and how does that deform each material) Be sure to use poissons ratio in the..

  Determine what is the elevation of the curve at station

An equal-tangent crest curve connects a +2% initial grade with a -1% final grade, and is designed for 55mi/h. The station of the PVI is 233 + 40 with elevation 1203 ft. What is the elevation of the curve at station 234+00

  Where the maximum ground level concentration would occur

a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash.

  Determine the magnitude of the reaction force exerted at b

When the engine of the plane is running, the vertical reaction that the ground exerts on the wheel at A is measured as 616lb . When the engine is turned off, however, the vertical reactions at A and B are 520lb each.

  What is the width of the second floor

A cross section of a cottage, 20 ft wide, is an isosceles triangle. If the slope of a side is 1.75 and there is a second floor 8 ft above the ground floor, what is the width of the second floor?

  Calculate the detention time

As a consulting engineer you are hired to evaluate the operation and the unit processes within the plant and make recommendations for improvements. You are asked to consider the following units.

  Determine void ratio and the porosity of undisturbed soil

A sample of undisturbed soil has a dry weight of 10 lb and volumen of 1 ft^3. If the specific gravity of the soil solids is 2.65, determine the void ratio and the porosity.

  Determine the work developed of air flowing through turbine

Neglecting kinetic and potential energy changes and assuming the ideal gas model determine the work developed of air flowing through the turbine

  How much will each leg shorten under the applied

given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)

  What would be average length of queue and waiting time

At a parking lot, vehicles arrive according to a Poisson process and are processed (parking fee collected) at a uniform deterministic rate at a single station. The mean arrival rate is 4 veh/min and the processing rate is 5 veh/min.

  Magnitude of the acceleration of the train

The train passes point A with a speed of 30 m/s and begins to decrease its speed at a constant rate of at = - 0.25 m/s2. Determine the magnitude of the acceleration of the train when it reaches point B, where sAB = 412 m.

  Find flow rate and the pressure head at the base of nozzle

The entrance to the pipe is reentrant, with ke = 0.9, and the nozzle loss coefficient is 0.045. Find the flow rate and the pressure head at the base of (entrance to) the nozzle.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd