Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
the signal shown below is a sine wave as it might be displayed on an oscilloscope. If it takes 40 msec. for the waveform to travel between the points shown by the arrow "B" below, what is the frequency of the waveform?
1.Convert 5EDA into binary number. What makes base 16 (Hexadecimal) an attractive numbering systems for representing values in computers 2. What is 4365 - 3412 when these values represent unsigned 12-bit octal numbers
Interface TTL logic to 120 VAC lamp. In this part of the lab, you will interface lowpower solid state electronics to the "outside world" by switching the 120 VAC lamp on and off using the AND gate from the previous experiment.
the cut-off frequencies of a series resonant circuit are 5400 Hz and 6000Hz. a. find the bandwidth of the circuitb. If Qs is 9.5 , find the resonant frequenciy of the circuit c. if the resistance of thecircuit is 2 ohms, find the value of Xl andXc at..
The standard method of representing negative numbers in the binary system is with 2's complement notation. Let's start by discussing why this is the case. What are the advantages and disadvantages of using this method to represent negative numbers
A 1 F capacitor is being charged through a 100 Ohm resistor. How long will it approximately take for the capacitor to reach about 63% of its final charge.
A balanced three-phase distribution line has an impedance of 1+j8 I per phase. This line is used to supply 3 balanced three-phase loads that are connected in parallel. The 3 loads are L1= 120 kVA at 0.96 leading pf, L2= 180 kVA
(a) a circuit in which one fuse will be damaged and other three not, after making all connections as per you schematic and connecting power supply (b) a circuit in which two fuses will be damaged and other two not,d connecting power supply
The power is generated by a DC power facility at a voltage of 10 V and deliver by two power lines with resistance Rline=3 ohm. The maximum power the voltage source can deliver is 5 W. a) Find the total power delivered by this DC voltage source
Typical gearing for most bicycles ranges from 30 to 50 teeth on the chain wheel and 12 to 30 teeth on the rear cog. Find how many more revolutions of the pedals the mountain biker will make during 480 miles trip using average pedaling time
(a) The ideal delay system. y[n] = x[n-nd] (b) The accumulator system. y[n] = sum (xk) , k from -inf to n (c) Forward difference system. y[n] = x[n + 1]- x[n] (d) Backward difference system. y[n] = x[n]- x[n - 1]
F = B'D' + A'B'C + ABC + CD' Draw a circuit for this function using only AND , OR, and NOT gates. The function calls for two 3-input AND gates and one 4-input OR gate. All you have available, however, are 2-input AND and OR gates
Refer to the Wheatstone Bridge diagram. If R1=1ohm, R2=111ohm, Runknown= 1ohm, R3 is set at 1Kohm, and the battery is 9V:What is the current flowing through the galvanometerohm Use 60ohm for the internal galvanometer resistance in calculations.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd