Determine what is the drag coefficient at sea level

Assignment Help Civil Engineering
Reference no: EM13309404

A 2,150 lb car is traveling at sea level at a constant speed. Its engine is running at 4500 rev/min and is producing 150 ft-lb of torque. It has a driveline efficiency of 90%, a driveline slippage of 2%, 15-inch radius wheels and an overall gear reduction ratio of 3 to 1. If te car's frontal area is 19.4 ft2, what is the drag coefficient?

Hint: it is important to keep track of all known values and the handful of equations that related them. Ultimately you should be able to solve for a vlaue of Fe, V, frl, Rrl. With these solved (plus a few given values) you should be able to use another equivalency for Fe that allows you to solved for CD.

Reference no: EM13309404

Questions Cloud

State solution is made by combining acetic acid with sodium : A solution is made by combining 15.0mL of 16.5M acetic acid with 5.52g of sodium acetate and diluting to a volume of 1.50L Calculate the pH
Estimate the potential difference across the resistor : The current through a 908 ohm resistor is 189 mA; to the nearest volt, what is the potential difference across the resistor
Determine the magnitude of the frictional force : A box of bananas weighinh 40 N rests on a horizontal surface. The coefficient of static friction between the box, the magnitude of the frictional force is
Explain the initial pressures of the components : For the reaction N2O4(g) (equilibrium arrows) 2NO2(g), kp = 0.25 at a certain temperature. Calculate the equilibrium pressures of NO2(g) and N2SO4(g) if the initial pressures of the components when placed in an otherwise empty container are as f..
Determine what is the drag coefficient at sea level : A 2,150 lb car is traveling at sea level at a constant speed. Its engine is running at 4500 rev/min and is producing 150 ft-lb of torque. It has a driveline efficiency of 90%, a driveline slippage of 2%, 15-inch radius wheels and an overall gear r..
Define the next maximum amount of "y" recrystallized : 0.12g of compound "Y" dissolves in 10ml of acetone @ 25 deg C and 0.85g of the same compound dissolves in 10 ml of boiling acetone. If 5g of compound "Y" were to be recrystallized from 75 ml acetone, what will be the next maximum amount of "Y" tha..
Explain radical formed by h-abstraction from diethyl ether : Radical formed by H-abstraction from diethyl ether. Showing curved arrows to where it goes.
What would be the design speed for passenger cars : Testing has shown that at a local race track (0.25 in length) racecars have a maximum side friction factor of 0.08. The smallest turn radius on the oval track is 150 feet and has a banking of 20 degrees.
Find the angle between the thread and a vertical line : A charged particle of mass m and charge q is suspended from a light thread in a region of space where there is a uniform horizontal electric field. find the angle between the thread and a vertical line

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the final temperature of xe in degree c

Two m^3 of xenon(Xe) are contained in a closed rigid tank at 70 degree C and 2 bar. The tank is heated to a pressure of 10 bar. Assuming that Xe behaves like an ideal gas with a specific heat ration of 1.7

  Determine what force was needed to buckle the bar

On a very hot day, I saw a 1.6 meter long steel bar held between two rigid supports that had buckled due to the heat. The bar had a cross section of 10 mm by 40 mm, and I assume was A36 steel.

  What should be the design q used in the full scale system

The flowrate (q) per unit lenght (ft^2/s) over the spillway shown below is a fuction of the upstream heah H, the acceleration due to gravity g, and the spillway height P.

  Thermal conductivities of aluminum and copper

The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..

  How to calculate the increase in weight of the tank

water flows into a weigh tank for 30 minutes. Calculate the increase in weight of the tank, if the discharge is 1.5 ft^3/s. The temperature is 50 F.

  Determine what is the final temp and the final mass of air

an insulated tank is evacuated. Air from the atmosphere at 12 psia and 70 degrees farenheight is allowed to flow into the 100 cubic foot tank. What is the final temp and the final mass of air in the tank just after flow ceases.

  Write a vba function that receives a variable name

Write a VBA function that receives a variable name plus four known values and then solves the ideal gas equation for a specified variable.

  What are the annual runoff coefficient for the sub areas

What are the annual runoff coefficient (Runoff /Rainfall ratio) for the sub areas and for the total watershed taken as whole Sub-area Area (m2)/ Annual Precipitation (mm)/ Annual Evaporation (mm) A 10.7 1030 530 B 3.0 830 438 C 8.2 900 430 D 17...

  Structure project design in civil engineering

Land is extremely valuable in this area therefore to win this job you need to consider innovative approach to reduce the waste areas

  Determine the pressure head at the top of the dome

A closed cylindrical tank filled with water has a hemispherical dome and is connected to an inverted piping system. The liquid in the top part of the piping system has a specific gravity of 0.68.

  Calculate stress along edge c-d caused by applied force

A horizontal prestressing force of 500kN is applied to a rectangular beam. The beam has a depth of 450mm and a width of 250mm. The force is applied at a distance of 60mm below the sections x-x axis.

  Determine the vertical force exerted by the balloon

A ballon is tethered at a height of 16.8 m above the ground by three cables. if the tension in highlighted cable is 60 N , determine the vertical force exerted by the balloon at the base of the balloon basket.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd