Determine what is the dc voltage from a full wave rectifier

Assignment Help Electrical Engineering
Reference no: EM13279274

A starter motor in a car has an armature 20cm long, diameter 10 cm, and slots .5 cm deep filled with windings. The radial field is provided by the coils in the stator to obtain a flux density of .2 Wb/m^2 so that there is one south and on the opposite side, the north pole. The coils on the rotor, 10 turns per coil, are connected in series through the commutator so that at any instant of time there are 5 coil sides under each pole. What is the torque on the rotor when 1 A flows through the coils? If this were an alternator rotating at 1000 rpm, what is the dc voltage from a full wave rectifier?

Reference no: EM13279274

Questions Cloud

Where on the other side must the second child sit : Two children are playing on a balanced seesaw. One child with a mass of 48 kg sits 1.4 m from the center. Where on the other side must the second child sit
Well-developed economies entering markets : We typically focus on firms from well-developed economies entering markets of less developed economies. Do firms from less developed economies have a chance of success if they enter developed markets, such as the United States?
Determine how deeply the signal penetrates for the objects : An object in a microwave oven 25 cm in diameter and 4 cm thick is being warmed. Determine how deeply the signal penetrates if the objects εr is 12.5 and σ is 2 S/m at a frequency of 2.5 GHz. Assume that the plane wave calculations are valid.
State what is the de broglie wavelength in cm : What is the de Broglie wavelength in cm, of a 12.7 g hummingbird flying at 1.15 multiplied by 102 mph? (1 mile = 1.61 km.)
Determine what is the dc voltage from a full wave rectifier : The radial field is provided by the coils in the stator to obtain a flux density of .2 Wb/m^2 so that there is one south and on the opposite side, the north pole. The coils on the rotor, 10 turns per coil, are connected in series through the commu..
Find the standard deviation : Given the following probabilities and returns for Mik's Corporation, find the standard deviation. Probability Returns 0.04 7% 0.25 4% 0.15 18% 0.20 10%
Stage of economic development-political-legal environment : Such a discussion should include the country's (a) stage of economic development, (b) political-legal environment, (c) technological environment, and (d) cultural environment. Also explore how entrepreneurship and business failure are perceived in th..
Derive a hazard-free realization of the function : Derive a hazard-free realization (and show that it is hazard-free), of the function AC+BCD+A'B'D' using only 2-input NAND gates, assume inputs are available uncomplemented and complemented.
What is the project depreciation expense : No change innet working capital is expected. Marginal profits will be taxed at a 35 percent rate. If the project's operating cash flow is $1 million, what is the project's depreciation expense? Its net income?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate rms value of the voltage across the 6 ohm resistor

The R2= 6 homs load in the circuit is absorbing four times as much average power as the R1 = 20 ohmsohms load. The two loads are matched to the sinusoidal source that has an internal impedance of 500 (angle) 0 1)What is the numerical value of a1

  Resize lighting system assuming a lighting level at bench

An office building of 20,000 ft2 would then take 40,000 watts of lighting at 2 watts /ft2. which amounted to 667 - 60 watt light bulbs or about the same two-bulb fluorescent fixtures. Resize the lighting system (W) assuming a lighting level.

  Provide the complete code-word including the checksum

The 24-bit data field of a packet is given by 0xBC603F. The packet contains a CRC with the generator polynomial given by X 3+X+1 a) Find the CRC checksum. Provide the complete code-word including the checksum in hex.

  Calculate the average voltage across the load

A single-phase, half-wave SCR circuit is used to control the power consumption of an inductive load. The resistive component of the load is 5 Ohm. The source voltage is 120 V (rms). When the triggering angle is adjusted to 60 degrees

  Design multi-stage audio amplifier for delivering avg power

Design a multi-stage audio amplifier for delivering an average power of 400 mW to a 16 Ohm speaker from a microphone that produces a 10 mV peak sinusoidal signal and has a source resistance of 1 kW. Use standard NPN QN2222 for your design.

  How much voltage is assumed dropped across a diode

(1) If you have a transformer that is not in a circuit, how can you tell/determine what the ratio is (2) How do you tell if a diode is forward or bias. How much voltage is assumed dropped across a forward biased silicon diode.

  What is the regulator output voltage when the supply is high

Design a 7.5-V zener regulator circuit using a 7.5-V zener specified at 12mA. The zener has an incremental resistance r(z) = 30 ohms and a knee current of 0.5mA. The regulator operates from a 10-V supply and has a 1.2k-ohm load.

  Determine output frequency for frequency division circuit

Determine the output frequency for a frequency division circuit that contains 12 flip-flops with an input clock frequency of 20.48 MHz.

  Design an opamp circuit to perfom the operations

Design an opamp circuit to perfom the following mathmatical operations on three seperate ideal voltage sorces, V1, V2, and V3. V0 = 10V1 + 4V2 - 8V3

  How can we increase the data rate in a digital signal

1. What is the effect of increasing the quantization levels on the quantization error in a PCM signal 2. How can we increase the data rate in a digital signal

  What is reflection coefficient if line is connected to load

A transmission line having a 50 ohm characteristic impedance is to drive a load of 200 ohms. 1)What is the reflection coefficient if the line is connected directly to the load 2) What is the standing wave ratio on the main line under the conditions o..

  Use the bounce diagram to plot

The line is terminated in a load RL = 25 ohm. Use the bounce diagram to plot V(t) at a point midway along the length of the line from t = 0 to t = 25 ns.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd