Determine what are the discharge and mass flow rate

Assignment Help Civil Engineering
Reference no: EM13315974

Water enters the lock of a ship canal through 180 ports, each port having a 2 ft by 2 ft cross section. The lock is 900 ft long and 105 ft wide. The lock is designed so that the water surface in it will rise at a maximum rate of 6 ft/min. For this condition, what will be the mean velocity in each port? What are the discharge and mass flow rate?

Reference no: EM13315974

Questions Cloud

Determine the temperature t and the specific volume : A turbine expands to a pressure of 10 kPa and a quality of 0.94. Determine the temperature T and the specific volume at this state.
Scarcity underlies the need for an economic system of any : Scarcity underlies the need for an economic system of any type. What is scarcity? Is it possible to ever eliminate scarcity? In what two ways could an economy try to eliminate scarcity? Will these attempts ever be successful?
Find what ratio of h by b gives the minimum value of nc : Repeat LEM(Limit Equilibrium Method) analysis in clay (undrained) using a circular failure surface, with the center of the circle a distance h above the edge of the footing. What ratio of h/B gives the minimum value of Nc
Demonstrate what is the marginal productivity of capital : What is the marginal productivity of labor? Demonstrate What is the marginal productivity of Capital? Demonstrate Is the productivity of the inputs a decreasing or an increasing function (does the function exhibit diminishing returns in each of the i..
Determine what are the discharge and mass flow rate : Water enters the lock of a ship canal through 180 ports, each port having a 2 ft by 2 ft cross section. The lock is 900 ft long and 105 ft wide. The lock is designed so that the water surface in it will rise at a maximum rate of 6 ft/min.
How much did the sound level change : You are standing 5 m from a tractor when the operator starts it ip the intensity is 3 x10^-5 W/m^2. How much did the sound level change
What assumptions can you make regarding the system : The flow is assumed to be laminar and the film thickness, H, constant. Using a coordinate system located on the plate at the surface of the pool, complete the following: a. Dram and sketch the system. Include coordinate system in your sketch.
Determine the resistance of the resistor : A capacitor that is initially uncharged is connected in series with a resistor and an emf source with E=110V, What is the resistance of the resistor
Graph the bond yield to maturity : Graph the bond yield to maturity (YTM) on the y-axis of an XY-scatter plot, with the bond to maturity in years on the x-axis and use a polynomial regression of order three to determine the relation between the YTM and the bond maturity.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What proportion of connectors fail during warranty period

The probability is 1% that an electrical connector that is kept dry fails during the warranty period of a portable computer. If the connector is ever wet, the probability of a failure during the warranty period is 5%.

  Compute how many grams of water must be added to soil

it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1000g of soil( in its natural state) in order to increase the water content 2..

  Explain how to determine the slant range r

The ball is released from position A and drops 0.75m to the incline. If the coefficient of resistitution in the impact is e=0.85, determine the slant range R. See Engineering Mechanics Dynamics meriam and Kraige 7th edition number 3/255 for figure

  Determine the cycle time for a single engine scraper

Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions. The average haul speed will be 14 mph and the average return speed will be 20 mph.

  What measurements should be laid out to establish a distance

a tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. what measurements should be laid out to establish a horizontal distance of 682.25ft

  Estimate the hourly so2 and particle emissions

what type of SO2 removal device before (in front of) or after (following) the particle collector would you use?

  What will be the force in newtons required

A lunar module weights 1500 kg on earth where g = 9.75 mps2. On the surface of the moon where g = 1.70 mps2, what will be the force in Newtons required to accelerate the module at 10 mps2?

  How much does the student have to pay at the end of 3 years

The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..

  Determine by trigonometry corresponding magnitude of r

Knowing that the magnitude of P is 35 N, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied to the support is to be horizontal, (b) the corresponding magnitude of R.

  Determine what is the periodic table form of the c-s-h gel

The C-S-H gel can come in a variety of chemical structure forms. If it has a cement notation form of C3 S2 H8, what is the periodic table form of this C-S-H gel. What would be the balanced equations for C3 S and C2 S when hydrated into this form

  Determine the minimum mean cell residence time

The initial waste concentration is 200 mg/l and the following constants have been determined: Ks=50 mg/l; k=5.0 days^-1; kd=0.06 days^-1; Y=0.60 Determine the minimum mean cell residence time, the mean cell residence time you would set for design.

  What is the isentropic efficiency of the compressor

An adiabatic argon unit compresses argon at 200 kPa and 27C to 2.18 MPa. If the Argon leaves this compressor at 513C. What is the isentropic efficiency of the compressor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd