User Account

All Pages

Determine volume of the tank and amount of heat transfer

Assignment Help Mechanical Engineering
Reference no: EM13708115

A rigid tank contains 10 lbm of air at 30 psia and 65°F. The air is now heated until its pressure doubles. Determine (a) the volume of the tank and (b) the amount of heat transfer.

Reference no: EM13708115

Questions Cloud

Running conveyor system problem : A random sample of three bottles is selected from the running conveyor system. When the bottles are inspected, they are either properly labeled or they are not. Rejected bottles are scrapped. The proportion nonconforming is 0.25. What is the probabil..
Insulated piston-cylinder-determine voltage of the soured : An insulated piston-cylinder device contains 7L of saturated liquid water at a constant pressure of 175 kPa. Water is stirred by a paddle wheel while a current of 6.2A flows for 75 min through a resistor placed in the water. If one half of the liquid..
Injection molding machine-what is minimum clamp tonnage : The bottom of a chair (where you sit, the ‘seat’) will be injection molded by itself in a mold. Assume the chair is a disk, 24 inches in diameter and 1/10 inch thick. If the injection pressure is 1600 psi, what is the minimum clamp tonnage you need f..
What is the total rate of their heat transfer : Metal balls 10 mm in diameter are to be annealed by heating them to 827°C then allowing them to cool slowly in air at 27°C to the point where they are in thermal equilibrium with the air. 2000 balls are annealed in one hour’s time. What is the total..
Determine volume of the tank and amount of heat transfer : A rigid tank contains 10 lbm of air at 30 psia and 65°F. The air is now heated until its pressure doubles. Determine (a) the volume of the tank and (b) the amount of heat transfer.
The vapor is to be saturated at the outlet of the turbine : A Rankine cycle with superheat is to be designed using water as the working fluid. The boiler pressure will be 1000 psia and the peak temperature will be 900 °F. (a) Determine the temperature required for the condenser if the expansion through the t..
Determine the mass of the refrigerant in the tank : A 0.5-m3 rigid tank contains refrigerant-134a initially at 160 kPa and 40 percent quality. Heat is now transferred to the refrigerant until the pressure reaches 700 kPa. Determine (a) the mass of the refrigerant in the tank and (b) the amount of heat..
Battery of silicon photocells mounted on plane surface : A battery of silicon photocells mounted on a plane surface operates with an efficiency of 16.7% under all conditions encountered in this problem. it is installed at a location 45 degrees north. the time is 10:00 on April 1, 1995. When the battery fac..
Assume ideal gas behavior with constant specific heats : The following cycle involves 3 kg of air. From 1 to 2 is polytropic compression where P1=150 kPa, T1=360 K, P2=750 kPa, V2=0.54 m^3 and n=1.2 . From 2 to 3 is constant pressure cooling and from 3 to 1 is constant temperature heating. Determine the to..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A hot rolled shaft is subjected to torsional load that

a hot rolled shaft is subjected to torsional load that varies from 320 nm clock wise to 120 nm anti -clockwise and an

  Using matlab solve the odes using any method

Capture the Rayleigh line between Mach number 0.2 to 4.0 initially by adding heat q in small increments taking the flow to M = 1 at location 2, there after removing heat until you achieve M = 4. Use the differential equations

  Oxygen-rich and virtually carbon-free environment

An iron-carbon alloy initially containing 0.55 wt% C is exposed to an oxygen-rich and virtually carbon-free environment at 1325 K. Under these conditions, the carbon diffuses from the alloy and reacts with oxygen at the surface.

  Determine the coefficient of restitution e and the velocity

The 500-lb ram of a pile drive falls 4 ft from rest and strikes the top of an 800 lb pile embedded 3 ft in the ground. Immediately after impact the ram is seen to have no velocity. Determine the coefficient of restitution e and the velocity v of the ..

  For a brief time the formula 1 championship held one of the

race cars often use wings in an effort to increase cornering speeds. the wings provide an extra downward force that

  Temperature difference between the hot and cold streams

A vortex tube is used to separate an ideal gas at 10 bar and 375 K such that half the gas is collected in a cool stream at 1 bar and 255 K and the other half becomes a hot stream at 1 bar and 495 K. Assuming the process is adiabatic: is this process ..

  Steam enters an adiabatic turbine steadily at 3 mpa and

steam enters an adiabatic turbine steadily at 3 mpa and 400 deg c and leaves at 70 kpa and 100 deg c. if the power

  What is the nominal value for density show the equation and

suppose we want to measure the density of a sample of argon. we cant measure it directly but we can measure pressure p

  Air at a rate of 10 lbms enters an adiabatic compressor at

air at a rate of 10 lbms enters an adiabatic compressor at 15 psia 80 f and leaves at 150 psia 740 f. calculate the

  What is the total force reaction

What is the total force reaction (magnitude) at pin joint O when the square plate is released from rest? Assume the plate has a uniform thickness.

  Find the elapsed time to vaporize the propane and total

a factory has a large liquid propane storage tank. the propane is to be used as vapor. evaporation of the liquid

  Prepare a case study based industrial visit report

Overview of the company which includes company background, major businesses, annual production, and major customers involved.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd