Determine torque t indicated by a gage reading

Assignment Help Civil Engineering
Reference no: EM13320173

A single strain gage is cemented to a solid 4-in diameter steel shaft at an angle B = 25 degrees with a line parallel to the axis of the shaft. Knowing that G = 11.6*10^6 psi, determine torque T indicated by a gage reading of 300*10^-6 in/in.

Reference no: EM13320173

Questions Cloud

Essentials of advanced financial accounting : In the "Essentials of Advanced Financial Accounting" Solutions, what do those like "1EXAAN" mean. Which question does it represent?
What is the acceleration of the lighter block : A 1.4Kg block and a 2.6kg block are attached to opposite ends of a light rope. what is the acceleration of the lighter block
Determine the specific heat of the unknown substance : An unknown substance has a mass of 0.125 kg and an initial temperature of 94.7. calculate the specific heat of the unknown substance
What is the replacement of equipment : Columbia Enterprises is studying the replacement of some equipment that originally cost $74,000. The equipment is expected to provide six more years of service if $8,700 of major repairs are performed in two years.
Determine torque t indicated by a gage reading : A single strain gage is cemented to a solid 4-in diameter steel shaft at an angle B = 25 degrees with a line parallel to the axis of the shaft. Knowing that G = 11.6*10^6 psi
Find the initial speed of this second balloon : In the annual battle of the dorms, students gather on the roofs of Jackson, A second balloon launched at the same angle hits the edge of Walton's roof. Find the initial speed of this second balloon
What is the area of longitudinal steel required for column : A short concrete column is being used to support the roof over a pedestrian walkway. The unbraced column length is 9 feet and supports a dead load of 12 kips and a live load of 20kips.
Choose a company and discuss their branding : Choose a company and discuss their branding.
Determine the initial speed of the bullet : A small wooden block with mass 0.875kg is suspended from the lower end of a light cord that is 1.80m long. What was the initial speed v0 of the bullet

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the tce concentration in mg per cubic meter

The concentration of trichloroethelyne (TCE) in an air sample near a hazardous waste landfill is 34 ppm, the ambient air temperature is 31 degrees C, and the atmospheric pressure is 0.94 atm. What is the TCE concentration in mg/m^3

  Determine particles position and the velocity of particles

The acceleration of a particle along a straight line is defined by a=(2t-9)m/s^2, where t is in seconds.At t=0, s=1m, and v=10 m/s. When t=9s, determine the particles position, the total distance traveled, and the velocity.

  Determine total volume of the sandy silt for construction

The in-situ bulk density of the sandy silt is 1.92 Mg/m^3 and its average water content is 13%. determine: a) the total volume of the sandy silt that must be removed from the borrow pit for construction of the embankment

  Find average rate of co emissions during two hour period

above a peninsula of land. the length of the box is 25 km, its width is 80 km, and a radiation inversion restricts mixing to 25 m. Wind is blowing clean air into the long dimention of the box at 0.8 m/s.

  Determine the pressure that develops in the container

A rigid-walled cubical container is completely filled with water at 40F and sealed. The water is then heated to 100F. Determine the pressure that develops in the container when the water reaches this higher temperature.

  Determine the average normal stress at the critical section

two 10 mm thick steel plates are fastened together by means of two 20mm bolts that fit tightly into the holes. if the joint transmits a tensile force of 45 kn determine the average normal stress in the plates at a section where no holes occur

  Find an expression for the diameter of the droplet

find an expression for the diameter, D, of the droplet, in terms of the specific weight and surface tension, assuming the contact angle just before seperating is zero.

  Determine the angle of twist of gears a and c

The 60mm diameter shaft ABC is supported by two journal bearings, while the 80mm diameter shaft EH is fixed at E and supported by a journal bearing at H. If T1= 2 kN*m and T2= 4 kN*m

  What is the mean section velocity in the expanded section

Water flows at 8 m^3/s through a rectangular channel 4 m wide and 3 m deep. If the velocity is 1 m/s, calculate the flow depth in the channel. If this channel expands downstream to a width of 5m and the depth decreases by 0.5m from the upstream de..

  Determine bulk density and the degree of saturation

A cylindrical sample of soil 39 mm in diameter and 77 mm long weighed 180 g. The sample is not fully saturated and its moisture content was found to be 27.0%. Assume rS = 2.70 Mg/m3. Determine: a. the bulk density, r b. the dry density, rd c. the d..

  Determine the largest distance x that the stream can reach

A nozzle discharges a stream of water with an initial velocity v0 of 50 ft/s into the end of a horizontal pipe of inside diameter d=5ft. determine the largest distance x that the stream can reach.

  How much atrazine is bound to soil and dissolved in water

Atrazine is adsorbed to a soil that is only saturated by 5%(i.e. only a twentieth of the pore volume is filled with water), how much atrazine is bound to the soil, dissolved in the water, and present as vapor in the gas phase

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd