Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.A plug-flow reactor has a conversion of A of 90%, and the reaction is first order. If a dispersed plug-flow reactor has the same volume and has a dispersion number, D/vL of 1.0, what will be the percent conversion?
2.What is the equation to get volume of cut and volume of fill if i used excel formulated , in construction methods.
3.A transmission tower is held my three guy wires attached to a pin at A and anchored by bolts b c and d if the tension in wire ab is 3.6 kn determine the vertical force p exerted by the tower on the pin at A
4.Air enters an insulated turbine operating at steady state at 4.89 bar, 597 deg. C, and exits at 1 bar, 297 deg C. Neglecting kinetic and potential energy changes and assuming the ideal gas model determine the work developed of air flowing through the turbine
A fine sand has a hydraulic condutivity of 3.5 x 10^-5 m/s a hydraulic gradient of 0.00141, and a porosity of 45 percent. Detrmine the Darcy velocity and the averge linear velocity
You add 100 mg/L of glucose to pure water, then decide that this was a mistake and decide to remove it biochemically before you serve the water to your friends at a cocktail party. To remove the glucose, you seed the water with a harmless bacteria..
what is the probability that less than 0.5 inches of precipitation will occur in any January? What is the probability that more than 2.5 inches wil
A Riehle Impact Testing Machine was used to break the specemins and the reading gave 68ft/lb, 66ft/lb, 64ft/lb, 69ft/lb and 63ft/lb. The cross section dimensions of the Charpy were measured to be 0.320in and 0.397in.
For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.
The water depth before the jump is 0.4 m and after the jump is 1.7 m. Compute the flow rate in the channel, the critical depth and the headloss in the jump.
A strong wind moves the air mass over a mountain range at 2,500 m. mean sea level and then the air descends to an elevation of 500 m on the leeward of the mountain.
Differntial Leveling between BM's A,B,C,D, and A gives elevation differences (in meters) of -15.632, 32.458, 38.214, and -55.025, and distances in km of 4.0, 6.0, 5.0, and 3.0 respectively.
In a short section of a channel carrying a steady discharge of 36 m^3/s, the depth is seen to increase from 1.6 m to 1.75 m. The channel is rectangular, 20 m wide with a bedslope of 0.0002 and Manning n of 0.014.
A pump in a large industrial hall containing 30 liters gasoline breaks down, causing the gasoline to spill into a 3 m2 sump surrounding the pump. The liquid pool is ignited by sparks. Assume the combustion to be 70% effective and the heat loss due..
compute the max possible moment at the centerline of the beam and the absolute moment in the beam.
Carnot engine working between a source temperature of T2 and sink temperature of T1 has efficiency of 25%. if the sink temperature is reduced by 20 degrees Celsius the efficiency is increased to 30%. find the source and sink temperature
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd