Determine the weight and cost of prepeg required to produce

Assignment Help Mechanical Engineering
Reference no: EM13629928

Determine the weight and cost of prepeg required to produce a hollow composite tube (Outside Diameter = 50mm, wall thickness = 5mm and, length = 4m) if it contains 60 volume percent AS-4 carbon fibers (at $60/Kg) in an epoxy matrix (at $8\kg). The tube is manufactured by wrapping the prepeg around a mandrel, and the cost of prepreggings is $70/kg.

Find the volume of tube, Find Carbon Fiber and epoxy density from internet, Calculate composite density using fiber volume fraction equation Pc=PfVf+(1-Vf)Pm, Total Cost = Cost AS-4 + Cost Epoxy + Cost of Fabrication.

Reference no: EM13629928

Questions Cloud

A 120 lbm base jumper extreme parachutist leaps from el : a 120 lbm base jumper extreme parachutist leaps from el capitan in yosemite national park 3000 ft vertical drop head
A certain airplane can accelerate on the runway at a rate : a certain airplane can accelerate on the runway at a rate of 2.5 ms2 and must attain a speed of 30 ms in order to take
A wind tunnel made of circular duct consists of a : a wind tunnel made of circular duct consists of a contracting nozzle a test section in which experiments are conducted
A researcher reports that there is no consistent : a researcher reports that there is no consistent relationship between grade point average and the number of hours spent
Determine the weight and cost of prepeg required to produce : determine the weight and cost of prepeg required to produce a hollow composite tube outside diameter 50mm wall
A rigid well insulated container with a volume of 2 ft3 : a rigid well insulated container with a volume of 2 ft3 holds 0.12 lb of ammonia initially at a pressure of 20 lbfin2.
Discharges heat to the atmosphere 20degc for operation at : a solar collector receives solar radiation at a rate of 0.315 kw per m2 and delivers the heat to a storage unit whose
An airplane heading eastward is observed to be in a : an airplane heading eastward is observed to be in a 20degree climb at a speed of 1200kmh. at this instant its
The value of the pearson r : the value of the pearson r indicatesa the strength of a linear relationship between two sets of ordinal data.b the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Lead shot is formed by dropping molten lead through the

lead shot is formed by dropping molten lead through the center of a high tower. the frictional resistance of the air as

  Estimate the theoretical kw electrical demand that this

a vapor compression refrigetarion cycle has a theoretical cop of 4.8 and provides 120000 btuh of cooling. the

  Assume that 350 kjkg of energy must be removed by heat

for each kw of power input to an ice maker at steady state determine the maximum rate that ice can be produced in kgs

  Air enters a compressor at 300 k and 100 kpa at a

air enters a compressor at 300 k and 100 kpa at a volumetric flow rate of 4 m3s. the air is compressed such that the

  Temperature and density of air for an adiabatic process

Effect of pressure on temperature and density of air for an adiabatic process, The pressure is to be raised from atmospheric to 7 psi (4.83 bar). The process is adiabatic, and the volume is constant and unknown.

  A steel tensile specimen with starting gage length 20 in

a steel tensile specimen with starting gage length 2.0 in and cross-sectional area 0.5 in2 reaches a maximum load of

  A uniform beamoflength l flexural rigidity ei and

a uniform beamoflength l flexural rigidity ei and cross-sectional plastic moment mp is built-in at both ends and

  Punger velocity u acceleration of gravity g water density

in an experimental study designed to simulate the manner in which a cat drinks a glass plunger simulating a cats tongue

  Determine a the pressure b the total internal energy and c

a 0.5-m3 vessel contains 10 kg of refrigerant-134a at -20oc. determine a the pressure b the total internal energy and c

  Calculate the isentropic work process 1-2s the actual work

air at mass flow rate of 10 kgs at 1 atm 300 k point1 enters an adiabatic compressor and exists at 8 atm 600 k point 2.

  Air at 50 psia and 90 f flows at the rate of 16 lbms

air at 50 psia and 90 f flows at the rate of 1.6 lbms through an insulated turbine. if the air delivers 11.5 hp to the

  Derive the equation of motion of the simple pendulum

derive the equation of motion of the simple pendulum consisting of a point mass m attached to a rigid wall by a string

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd