Determine the water flow rates through each plate

Assignment Help Mechanical Engineering
Reference no: EM13835552 , Length: 10 Pages

Minimum Length of Report: 10 Pages

Multiple effect evaporator with vacuum

• For a desalination plant which has a multiple effect evaporator as its main fresh water production system, determine:

- The temperature and enthalpy of the steam/vapour and the condensate at each step

- The energy used in each evaporator vessel to evaporate water and the quantity of water evaporated in one hour

- The minimum quantity of cooling sea water required to fully condense the No. 5 vapour if the initial water temperature is 25 C and a temperature rise of 8 C is allowed for a contact condenser

- The quantity of total fresh water produced for two cases (do not count the LP steam condensate): 1. use of a non-contact condenser, 2. use of a contact condenser

• Draw an schematic of the setup with flows and conditions

• Information: simplify by using fresh water properties. Salt water inflow is 600 t/h at 100 C (a preheater has been used), LP saturated steam flow is 100 t/h.

Steam conditions  Pressure (kPaabs)
LP steam  220
No.1 vapour  180
No.2 vapour  140
No. 3 vapour  100
No. 4 vapour  60
No. 5 vapour  15

P&ID for boiler and steam turbine system

• Prepare a P&ID diagram for a boiler and steam turbine system with a steam flow of 100 t/h, 20 bar, 350 C. Feedwater at 25 bar and 95 C.

Use the standards given in the lecture notes. Please include:

- turbine, condenser, condensate tank, subcritical boiler, feed water pump, feedwater control valve, feed pressure control valve with excess return to condensate tank, level control for condensate tank, level control for steam drum, attemperation control for steam temperature

• You can use a software package such as autocad, or submit it neatly hand drawn (or a combination). This is an assignment to show that you understand how to put together a P&ID diagram, not on how to use software.

Perforated plates in a clarifier

Two concentric perforated plates are separated by a 200 mm launder and form the flow exit for a clarifier (Figure 1). The inlet water flow of 1200 m3/h into the clarifier is through a 300 mm peripheral launder. The perforated plate information is in Table 1.

1. Determine the water flow rates through each plate by assuming the water flow rate is proportional to the plate area.

2. Determine the Reynolds number for the main body of the clarifier , compare it to the lower limit given on slide 4 and comment.

3. Determine the number of holes necessary in the inner plate to achieve the same pressure drop through both plates, state the value of the pressure drop.

4. Change the inner plate outlet flow to 400 m3/h, and while keeping other geometry the same, determine the hole diameter required for the outer plate to have the same pressure drop as the inner plate, state the value of the pressure drop.

• Use water properties at 20 C and atmospheric pressure. Sketch the side view and plan view with all dimensions. Use the equation for zeta. Hints: use an excel spreadsheet and the goal seek function. Detail the main variables and their values on paper. Submit your excel spreadsheet.

Table 1  Perforated plate details

Inside diameter(m) Outside diameter (m) No of holes  Diameter of holes (mm)
Inner plate  0.5 2.5 ? 20
Outer plate  2.4 4 900 20

Length : 10 Pages

Reference no: EM13835552

Questions Cloud

Sequential-move game between ann and bob : Question 1: Consider the following sequential-move game between Ann and Bob.
Taxonomy of leadership theories : Taxonomy of Leadership Theories
Explain what caused the rise of neopopulism in mexico : What caused the rise of Neopopulism in Mexico? and the most important question, What was the President Felipe Calderón's response to Neopopulism?
Give two examples of actions taken by the administration : Give two examples of actions taken by the administration of yourcollege whose effect is to prevent specific markets from reaching equilibrium
Determine the water flow rates through each plate : Determine the water flow rates through each plate by assuming the water flow rate is proportional to the plate area and determine the Reynolds number for the main body of the clarifier , compare it to the lower limit given on slide 4 and comment.
Find average arrival rate of telephone call to each employee : Average arrival rate of telephone calls to/from each employee's telephone? I (assume that this includes both outgoing and incoming calls and that? I will have the same value for all employees).
Production possibilities analysis : Production possibilities analysis implies that an individual nation is limited to the combinations of output indicated by its production possibilities curve. Do you agree or disagree with this statement?
How might this information affect the advertising strategy : Calculate an appropriate measure of association, and decide how to present the results. How might this information affect the advertising strategy
Why is the production possibility frontier bowed outwards : Why is the production possibility frontier bowed outwards?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd