Determine the volume of traffic across the bridge

Assignment Help Civil Engineering
Reference no: EM13533350

A bridge has been constructed between the mainland and anisland. The total cost (excluding toll) to travel across thebridge is expressed as C=50+0.5V, where V is the number of veh/dayand C is the cost/vehicle in cents. The demand for travelacross the bridge is V=2500-10C.

(a)Determine the volume of traffic across the bridge.

(b)If a toll of 25 cents is added, what is the volume acrossthe bridge?

(c) A tollbooth is to be added, thus reducing the travel timeto cross the bridge. The new cost function is?

Reference no: EM13533350

Questions Cloud

You are designing a highway bridge : You are designing a highway bridge. In particular you aretrying to determine how to put the road surface on the bridge. Youlive in an area where the maximum summertime temperature is 40 degrees centigrade and the minimum winter temperature is -30degr..
What would be her recoil velocity : In a football game, a receiver is standing still, having just caught a pass. Before he can move, a tackler, running at a velocity of +3.1 m/s, grabs him. The tackler holds onto the receiver, and the two move off together with a velocity of +1.6 m/s
Convert the bearings to azimuths from north : Convert the bearings to azimuths from north and compute theangle . smaller then 180 degree. between successive bearings.
How much energy in horsepower islost by the water while flow : A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.
Determine the volume of traffic across the bridge : A bridge has been constructed between the mainland and anisland. The total cost (excluding toll) to travel across thebridge is expressed as C=50+0.5V, where V is the number of veh/dayand C is the cost/vehicle in cents. The demand for travelacross the..
What is the average chear stress in the glue joint between : Two 1/2 inch rods are spliced together by glueing a 2 inch section of plastic pipe over the rods ends. If a tensile force P = 350 lb is applied to the spliced nylon rod, what is the average chear stress in the glue joint between pipe and the rods?
Calculate expected error l if a theodolite has direct : The bottom of a rectangular flume is 5mabove reference level. The depth of the water in the flume is 3m.The average velocity is 1.7 m/s. Compute the total hydraulic energyat the surface of the water and at the bottom of the flume.
Determine the critical point : The initial ultimate BOD after mixing of the Bergelmir Riveris 12.0 mg/L. The DO in the Bergelmir River after the wastewaterand river have mixed is at saturation. The river temperature is 10degrees celsius
Write a statement of electroneutrality for a solution : A groundwater has an alkalinity of 200 mg/L as CaCO3.Assume that all of the alkalinity is bicarbonate. Express thisbicarbonate concentration in units of meq/L, moles/L, and mg/L.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the depth of flow immediately upstream of the hump

A rectangular channel of 2 m depth and 5 m width carries 1 m deep running water. It is laid to a slope of 0.001 with Manning's n = 0.02. Some distance downstream there is a hump of height 0.5 m on the stream bed.

  What is the maximum accelaration from rest for the car

a newly designed car has a 9.2 ft wheelbase, is rear wheel drive, and has a center of gravity 18 inches above the the road and 4.3 ft behind the front axle. the car weighs 2450 lb, the mechanical effciency of the drivetrain is 90%, and the wheel r..

  Determine what will be carbondioxide level 10 years later

Assume to just using coal as an electric energy source. Take efficency as %50 for average power plant.If the carbondioxide level is 400 ppm by volume now, what will be the carbondioxide level 10 years later

  Define energy transfer in mechanical systems

Energy transfer in mechanical systems, A wheel is 800mm in diamiter and has a mass of 1000kg. on a horizontal surface without skidding, the vehicle accelerates uniformly at 0.5m/s^2 for 5 seconds.

  Problem 1 solve the following three questions of the beam

problem 1. solve the following three questions of the beam abc. note that a is a roller support b is a pin connection

  The j-shaped member shown in the figure is supported by a

the j-shaped member shown in the figure is supported by a cable de and a single journal bearing with a square shaft at

  Determine the net power output and thermal efficiency

An open system Brayton cycle is used in a power plant. The atmospheric inlet conditions of the compressor are: temperature 30C and pressure 100kPa and the pressure at its outlet is 1200kPa.

  What is the longest amount of time that particle can take

If the tank is 2 meters deep and the particle enters the tank at the surface of the water, what is the longest amount of time that the particle can take to settle, if it is to be removed

  How many plates are needed to collect with regulations

In order to comply with regulations, an iron/steel sinter plant installs an electrostatic precipitator (ESP) to collect 98% of the 10 ?m particles from an air stream flowing at 2 m3/s

  Explain how factors affect excavation operations and costs

Explain how the different physical characteristics and moisture content of soil lead to the different angles of repose, swell, and shrinkage factors. Explain how these factors affect excavation operations and costs.

  How much excess pore water pressure would need to develop

The vertical effective stress at a certain point in a loose sand is 1000lb/ft^2. If an earth quake were to occur, how much excess pore water pressure would need to develop at this point for liquefaction to occur

  Calculate the minimum flow rate

Calculate the minimum flow rate (m^3/hr) of river water needed to acheive pre cooling hot, pasteurized liquid prodcut assuming that 10% heat is lost to the surroundings during exchange and that the water temp after cooling should not exceed 25 deg..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd