User Account

All Pages

Determine the volume flowrate from the tank

Assignment Help Mechanical Engineering
Reference no: EM13888094

Water is siphoned from a large tank and discharges into the atmosphere through a 5 cm diameter tube as shown in below figure. The end of the tube is 1 m below the tank bottom, and viscous effects are negligible.

(a) Determine the volume flowrate from the tank.

(b) Determine the maximum height, H, over which the water can be siphoned without cavitation occurring. Atmospheric pressure is 101 kPa, and the water vapor pressure is 1.79 kPa. (The density of water is 1000 kg/m3).

Reference no: EM13888094

Questions Cloud

Characteristics of an entrepreneurial venture and a business : Describe the characteristics of an entrepreneurial venture and a small business
Discuss the roles of early adopters in the market : Discuss the roles of early adopters and network developments in the market acceptance process of innovation
What is an impairment loss : What is an impairment loss - what is a cash-generating unit and determine if an impairment loss exists for the nursery division and how is value in use for a cash generating unit calculated.
Value of economic activity : Coffee beans cost only a few cents when imported. But to buy a coffee at a coffee bar costs far more. What does this tell you about value added?
Determine the volume flowrate from the tank : Water is siphoned from a large tank and discharges into the atmosphere through a 5 cm diameter tube as shown in below figure. The end of the tube is 1 m below the tank bottom, and viscous effects are negligible.
Develop a pricing strategy for the higher-ranged products : Construct a strategy for managing the higher-ranged product brands. Provide a rationale for your strategy. Develop a pricing strategy for the higher-ranged products. Provide a rationale for your strategy
What are consequences of ingroup and outgroup categorization : What are the consequences of ingroup and outgroup categorization?
Prepare the flexible budget for manufacturing for quarter : Prepare the flexible budget for manufacturing for the quarter ended March 31, 2013. Assume activity levels of 900, 1,000, and 1,050 units.
Volume occupied by the steel : Assume that crude oil from a supertanker has density 750 kg/m'. The tanker runs aground on a sandbar. To reflect the tanker, its oil cargo is pumped out into steel barrels, each of which has a mass of 15.0 kg when empty and holds 0.120 m' of oil Y..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At a location where the local atmospheric pressure is 142

a manometer is connected to a water pipe to measure the pressure at the center of the pipe. the manometer is

  What is the required impeller diameter ratio between the

a 20 mw radial flow hydraulic turbine is to be designed with a head of 70 m and a speed of 90 rpm. a geometrically

  Steam at 1 bar enters an adiabatic heat exchanger with a

steam at 1 bar enters an adiabatic heat exchanger with a quality of 0.89 and exits as a saturated liquid. the steam is

  Determine the mass flow rate of steam

Steam enters a diffuser at and with a velocity of and exits as saturated vapor at 240 F and 100 ft/s. The exit area of the diffuser is 1 ft2. Determine the mass flow rate of steam and the rate of entropy generation.

  If the heating value of the natural gas fuel is 45000 kjkg

a gas turbine power plant produces a net power output of 100 mw with an overall thermal efficency of 35a if the heating

  The system contains a sharp-edged

a liquid at 10 c kinematic viscosity of 1.30710-6 m2s is to flow from a roof-top reservoir to a tanker truck through a

  Determine the outlet temperature of the hot fluid

Determine the outlet temperature of the hot fluid.

  Deduce the output speed characteristic

Deduce the output speed characteristic corresponding to an input signal of 24 volts as a step function

  A small heater insyde the sphere maintains the surface temp

air at one atmospheric pressure and at 20degc flows across a 12 mm diameter sphere witha free stream velocity of 5 ms.

  Linear velocity profile was used to model flow

A linear velocity profile was used to model flow in a laminar incompressible boundary layer in Problem 5.10. Express the rotation of a fluid particle. Locate the maximum rate of rotation. Express the rate of angular deformation for a fluid particle.

  Maximum allowed pressure within the cylindrical vessel

Consider a pressure vessel made by welding together two hemispheres of radius 20 ft and wall thickness 1.5 inches. If the allowed normal stress is 90 ksi, calculate the maximum allowed pressure within the spherical vessel.

  Find out the coefficients m and b of the function you

below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd