Determine the volume and density of the body

Assignment Help Civil Engineering
Reference no: EM13555142

1.The moist unit weights and degrees of saturation of a soil are given: moist unit weight (1) = 16.62 kN/m^3, degree of saturation (1) = 50%; moist unit weight (2) = 17.71 kN/m^3, degree of saturation (2) = 75%. Determine a) e (void ratio) and b) Gs (specific gravity)

2.the force-couple system at A is to be replaced by a single equivalent force acting at a point B on the vertical edge of the triangular plane. determine the distance d between A and B

3.the device shown is a part of an automobile seat-back-release mechanism. The part is subjected to the 4 N force exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force.

4.The volume and the average density of an irregularly shaped body are to be determined by using a spring scale. The body weighs 7200 N in air and 4790N in water. Determine the volume and density of the body. State your assumptions.

Reference no: EM13555142

Questions Cloud

What will be the porosity of the mixture : You are furnished with three sizes of particles. One is gravel with porosity of 0.32, the second is a coarse grained sand with porosity of 0.37, and the third is a fine grained sand with porosity of 0.23. If the coarse grained sand
Determine redox state of sulfur in both the compounds : Derive the porosity values for cubic, orthorhombic, and rhombohedral packing of spheres. Include sketches supporting your calculations of the bulk volumes of the unit cells.
Calculate the plasticity index the liquidity index : The soil is under a rectangular concrete slab 15m x 50m, used as a foundation for a building. A water pipe, in diameter id located in a trench 450mm below the center of the slab. The trench running along the length of the slab,300mm wide and 450mm de..
Will johnsons actions have any implications for future : In this case, it seems clear why Johnson is tempted to omit references to the ambiguous data. He is understandably anxious to graduate and move on to other challenges in his professional life. He is worried that full disclosure of his findings could ..
Determine the volume and density of the body : The volume and the average density of an irregularly shaped body are to be determined by using a spring scale. The body weighs 7200 N in air and 4790N in water. Determine the volume and density of the body. State your assumptions.
What is the absolute pressure at the surface of the mercury : An airplane is flying at 10.6 km altitude. in its nonpressured cargo bay is a container of mercury 325 mm deep. The container is vented to the local atmosphere.
How long will it take for consolidation of a similar clay : A clay specimen, 1 in thick (drained on top and bottom), was tested in the laboratory. For a given load increment, the time for 50% consolidation was 5 min 20 sec. How long will it take for 50 % consolidation of a similar clay layer in the field that..
Compute the gravimetric water content : A sample of clay was obtained from a point below the water table. An oven-drying test performed on this sample resulted in the following data:
Calculate air-dry moisture content : The weight of a sample of coarse aggregate was measured under various conditions with the following results:

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the rolling resistance

He is concerned about the high rolling resistance of the units in the sand (RR factor 250lb/ton).  What is the rolling resistance?

  Calculate the hydraulic conductivity if the porosity of sand

A constant-head test was conducted on a sample of soil 15cm long and 60 cm^2 in cross-sectional area. The quantiities of water collected was 50 cm^3 in 20 seconds undera a head difference of 24 cm.

  Determine flow rate of water that will cause a pressure drop

Determine the flow rate of water (20 degrees celcius) that will cause a pressure drop of 17250 N/m^2 in 350m of horizontal, cast-iron pipe (d=60cm). assume minor losses are negligibe

  Find what is the mean velocity relative to the cylinder wall

if the sphere falls at a speed of 150mm/s, what is the mean velocity relative to the cylinder wall of the water in the gap surrounding the midsection of the sphere

  Determine the change inside diameter when the gun is fired

a navel gun (E= 30,000 ksi and G = 11,600 ksi) with a bore of 16 in. develops a maximum internal pressure of 20,000 psi. Determine a. the minimum outside diameter required if the maximum tensile stress permitted in the gun barrel is 36,000 psi.

  Determine the temperature of propane in the tank drops

determine the temperature of propane when the pressure in the tank drops to 1 atm. Also determine the total amount of heat transfer from the environment to the tank to vaporize the entire propane in the tank.

  Determine the average impulsive force developed

The 180-lb iron worker is secured by a fall-arrest system consisting of a harness and lanyard AB, which is fixed to the beam. If the lanyard has a slack of 4 ft, determine the average impulsive force developed in the lanyard if he happens to fall 4 f..

  Calculate the ammonia concentration in mg per l

NH4+ = N+ + NH3 pK =9.24 If the pH is 8.5 and the ammonium(NH4+) concentration in 20mg/L, calculate the ammonia(NH3) concentration in mg/L.

  Calculate weight percent austenite and weight proeutectoid

a .65% Carbon hypoeutectoid plain carbon steel is slowly cooled from 950 degrees C to just slighty above 723 degrees C calculate the weight percent austenite and weight proeutectoid ferrite in this steel

  What is the pressure drop for water at 60 degrees f flowing

What is the pressure drop for water at 60 degrees F flowing through 12in schedule 40 pipe at a rate of 500gal/min over a distance of 100 feet.

  What is the maximum amount of soluble

If the solubility product of magnesium hydroxide is 11.25 answerthe following question. If water at 25-degree C is bufferedsuch that the pH remains fixed at 7, what is the maximum amount ofsoluble Mg2+, in grams, in 1L of water?

  The fixture ac is designed with a screw adjustment to

the fixture ac is designed with a screw adjustment to regulate the height of the 900 n load supported by the roller

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd