Reference no: EM131658756

Question 1. FIGURE 1 shows the block diagram of a superhetrodyne radio receiver. In a test a 20∝V signal was fed from the aerial into the first stage of the receiver, a radio frequency amplifier. This signal is the passed through several stages of the receiver to eventually appear at the input to the AM detector. For the AM detector to work satisfactory it requires a minimum signal level of -3dB(mW). Calculate the required minimum gain of the fifth intermediate amplifier given the data in TABLE 1.

Stage	Gain
RF amplifier	+10 dB
Mixer	-7 dB
BPF	-1 dB
IF1	+15 dB
IF2	+15 dB
IF3	+20 dB
IF4	+10 dB

TABLE 1

FIG. 1

Question 2. As a rule of thumb, the perceived noise from a source falls by 6 dBA with every doubling of the distance from the source.

If a 1 MW wind turbine (FIGURE 2) produces 103 dBA of noise within one metre of its base, estimate the distance from the turbine at which the noise can be reckoned to have fallen below the background noise level of 40 dBA.

FIG. 2

Question 3. A simplified model of ADC noise refers the noise to a noisy input source resistance Rn while assuming the rest of the signal path to be noiseless. FIGURE 3 represents a particular 18-bit ADC that has a 10 V input voltage range. The ADC has a bandwidth of 1 MHz.

Calculate the maximum value of Rn if the resolution of the ADC is not to be adversely affected by thermal noise. Assume the ADC operates at 25°C.

[N.b. The voltage resolution of an ADC is equal to its overall voltage measurement range divided by the number of discrete values possible on its output.]

FIG 3.

Question 4. The specification for a 4-way TV antenna amplifier [FIGURE 4] is given in TABLE 2, below.

Bandwidth	40-862 MHz
Gain	20 dB
Noise Figure	6 dB
Max. Output	85 dBµV
Input Impedance	75 ?
Output Impedance	75 ?

TABLE 2

FIG. 4

(a) Determine the voltage required on the input of the amplifier to give the maximum output of 85 dB∝V.

(b) If the signal level from the aerial is 5 dBmV and the input noise level is 20 dB∝V, calculate the signal-to-noise ratio on the output of the amplifier.

Question 5. A voltage amplifier ideally should have the input-output relationship of v_o = 100v_i but in practice the relationship is v_o = v_i(98 + 2v_i).

Calculate the %age second harmonic distortion present in the amplifier's output for a sinusoidal input of 10 mV r.m.s.

Question 6.

You may find the following relationship helpful in answering this question:

For a lossless line:

The characteristic impedance is given by Z_o = √L/C and the velocity of propagation by v_p = 1/√LC

where L and C are, respectively, the line's inductance and capacitance per metre length.

A transmission line is formed by two identical parallel tracks in a printed circuit board, as depicted in FIGURE 5. The line has a length of 50 mm and all line terminations are of 70 ?. The line can be assumed to be lossless.

(a) Use equations (4) and (5) from the lesson to calculate the magnitude of the NEXT and FEXT voltages generated in the victim conductor when the source voltage, Vin, in the aggressor conductor is a voltage step of 2 V with a rise time of 100 ps.

[Note that the V_s voltage at the input to the aggressor conductor is

V_s = V_in. R_in/(R_in + Z)

(b) Sketch the NEXT and FEXT waveforms.

The relevant parameters for the line are listed in TABLE 3.

FIG. 5

Parameter	Value
Line inductance	400 nH per m
Line capacitance	80 pF per m
Mutual inductance	80 nH per m
Mutual capacitance	10 pF per m

TABLE 3