Determine the velocity of flow find the discharge in cfs

Assignment Help Civil Engineering
Reference no: EM13563844

1.A paved parking lot section has a uniform slope over a length of 100 m (in the flow direction) from the point of a drainage area divide to the inlet grate, which extends across the lot width of 30 m. Rainfall is occurring at a uniform intensity of 10 cm/hr. If the detention storage on the paved section is increasing at the rate of 60 m3/hr, what is the runoff rate into the inlet grate?

2.What mass of lead nitrate [Pb(NO3)2] must be dissolved in 1 L of water to produce a solution that contains 20 mg of lead ions? Assume 100% ionization.

3.Given a V-shaped channel with a bottom slope of 0.001, a top width of 12ft, and a depth of 6 ft, determine the velocity of flow. Find the discharge in cfs and m^3/s.

Reference no: EM13563844

Questions Cloud

What is the generic soil cleanup criteria for direct contact : Based on Michigan law, (a) what is the generic soil cleanup criteria for direct contact with residential soils contaminated with lead? Report your answer in units of "ppm" (
Calculate the water content and degree of saturation : A jet of water of diameter 75mm moving with a velocity of 25m/s strikes a fixed plates in such a way that the angle between the jet and plate is 60? find the force exerted by the jet on the plate. (a) In the direction normal to the plate and (b) In t..
The self resistance of a practical inductor : The self resistance of a practical inductor is (A) in series with the inductance. (B) in parallel with the inductance. (C) responsible for storing the magnetic energy. (D) No correct answer listed Capacitive reactance XC is:
Calculate the depth of flow upstream of the bridge : Calculate the depth of flow upstream of the bridge assuming that the pier coefficient of drag is 1.2. Drag Force CD Af (V1^2)/2 CD=1.2
Determine the velocity of flow find the discharge in cfs : Given a V-shaped channel with a bottom slope of 0.001, a top width of 12ft, and a depth of 6 ft, determine the velocity of flow. Find the discharge in cfs and m^3/s.
Determine the max velocity and acceleration of b : A brass (nonmagnetic) block A and a steel magnet B are in equilibrium in a brass tube under the magnetic repelling force of another steel magnet C located at a distance x=.004 m from B
Determine the deviation at the top of the trajectory caused : A fireworks shell is launched vertically from point A with speed sufficient to reach a maximum altitude of 500ft. A steady horizontal wind causes a constant horizontal acceleration of 0.5ft/sec^2, but does not affect the vertical motion. Determine th..
Write a user friendly computer program to design torsion : Write a user friendly computer program to design torsion reinforcement in rectangular and flanged beams, and plot the cross-sectional reinforcement details on a graphic plotter
Determine distance the officer traveled before overtaking : A police car parked in a 45 mi/h speed zone observes a passing car traveling at a slow, constant speed. The officer believes the driver is intoxicated and begins accelerating uniformly to 50 mi/h in 8 seconds and maintains a constant velocity of 60 m..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate population for year 2011 assuming population growth

In 1800 an undeveloped country had a population of 10 million with birth and death rates of 60 and 52 per thousand per year. The situation continued until 1900, when the death rate instantaneously was reduced to 10

  What is the elevation of n held vertically at point m

A transit was set at point M and a leveling rod was held vertically at point N. The horizontal cross line of the telescope was inclined so the reading of the horizontal cross line on the rod was 12 ft.

  How to select the lightest available w33 section

the 30 ft simple beam shown has lateral support spacing at 15 ft for its compression flange and consists of 50 ksi steel. the beam supports a gravity service dead load of 1.2 klf (includes beam weight) and a gravity live load of 3.4 klf

  Compute the circumferential stress to which the wall

The length of a reading room in a library is 10 m and its breadth is 8 m. Compute the distributed live load, assuming the basic value of the load to be 2873 N/m2.

  Select a hydraulic pump size and a hydraulic cylinder size

An engineer is designing a hydraulic lift with a capacity of 10 tons. the moving parts of this lift weigh 1000lbf. the lift should raise the load to a height of 6ft in 20 seconds. This will be accomplished with a hydraulic pump

  Show that the model and prototype reynolds numbers are not

Show that the model and prototype Reynolds numbers are not equal, but sufficiently large for approximate dynamic similitude. For the length scale in the Reynolds number, does it make a dierence if you choose building height or building width? Which d..

  Determine the maximum stress on the beam

draw shear and bending moment diagrams determine the maximum stress on the beam (E=2.0E+11Pa) a simply supported beam AB is 5 m long carrying a uniform distributed load of 10kn/m over a 4m span

  Determine what is the first-order decay rate constant

A minimum contact time of 30 min is required to reduce the pathogen concentration from 100 pathogens/L to below 1 pathogen/L through a first-order decay process. You plan on treating water at a rate of 1,000 gal/min.

  Determine the rankine earth pressure diagram

A ten-foot high wall will retain a medium dense sand backfill. Determine the Rankine earth pressure diagram and the total active force on the wall.

  How does the engineering classification of soils differ from

A sample of undisturbed soil has a dry weight of 10 lb and volumen of 1 ft^3. If the specific gravity of the soil solids is 2.65, determine the void ratio and the porosity.

  Determine the volume of irrigation water needed in ac-ft

A crop has a consumptive use requirement of 1.2 acre-ft of water per acre of crop land. The crop is planted on 780 acres. Precipitation is 3.2 inches. The remainder of the 1.2 ac-ft/ac requirement is met by irrigation.

  What is the optimal distance between the two drainage canals

To avoid the salinization of soil in a farming area, parallel drainage canals are to be installed to maintain the water table at a depth of at least 4m below the ground surface. It is thought that no evapo-transpiration would occur below that depth. ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd