Determine the velocity and thermal boundary layer thickness

Assignment Help Civil Engineering
Reference no: EM13306097

Engine Oil at 60 degrees C flows over a 3m long and 2m wide plate whose temperature is maintained at 20 degrees C with a velocity of 2 m/s. Determine the rate of heat transfer from the entire plate. Also determine the velocity and thermal boundary layer thickness.

Reference no: EM13306097

Questions Cloud

Design the drilling - blasting pattern : Design the drilling - blasting pattern showing hole diameter, hole depth, burdens, spacings, explosive types, primers and initiation system and indicate the initiation sequence.
How much heat per second is being removed from the unit : A refrigerator has a surface area of 6.04 m2. It is lined with 0.0885-m-thick insulation whose thermal conductivity is 0.0300 J/(s m C °). How much heat per second is being removed from the unit
Obtain the temperature of the bar : One end of a brass bar is maintained at 305 oC, while the other end is kept at a constant, but lower, temperature. What is the temperature of the bar at a point 0.129 m from the hot end
Find increase in temperature of the brakes : A 768 kg car moving at 27 m/s brakes to a stop. The brakes contain about 16 kg of iron that absorb the energy. What is increase in temperature of the brakes
Determine the velocity and thermal boundary layer thickness : Engine Oil at 60 degrees C flows over a 3m long and 2m wide plate whose temperature is maintained at 20 degrees C with a velocity of 2 m/s. Determine the rate of heat transfer from the entire plate.
What will be the time- mean speed and space-mean speed : Assume you are an observer standing at a point along a three- lane roadway. All vehicles in lane 1 are traveling at 30 mi/ h, all vehicles in lane 2 are traveling at 45 mi/ h, and all vehicles in lane 3 are traveling at 60 mi/ h.
What contributed to the success of the initiative : 1. Discuss an organizational change you have encountered that was successful. What contributed to the success of the initiative? What barriers were overcome to reach success?
Determine what is the departure rate at a parking lot : The arrival rate at a parking lot is 6 veh/ min. Vehicles start arriving at 6: 00 P. M., and when the queue reaches 36 vehicles, service begins. If company policy is that total vehicle delay should be equal to 500 veh-min
What horizontal distance does it travel : If the ball was hit when it was 1.2m above the ground, what horizontal distance does it travel before it lands on the building

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate aeration basin size and the wate sludge rate

A completely mixed activated-sludge plan is being designed for a wastewater flow of 3.0 mgd. The BOD of 225 mg/l is 200 mg/l soluble. The effluent soluble BOD requirement is 7 mg/l (70 percent of the total 10 mg/l).

  Determine the force members bc, fc, and fe

Determine the force members BC, FC, and FE, and state if the members are in tension or compression.

  How much dividend income will receive over the next year

A corporation issues a new 10 year bond that has a coupon rate of 4.65% with quarterly dividend payments. Alex purchases 200 of these bonds at a price of $98.75, for a total investment of $19,750. Assuming he holds them to maturity, what will be..

  Draw thermal circuit of heat flow from center of pipe to t

Steam at 100 psia, sat vapor is in a pipe. The pipe is schedule 40 steel with a wall thickness of 1/8 inch and a length of 100 ft. The outside air temperature is 40 degrees Fahrenheit. The mass flow of steam is 4,000 lb/hr.

  Filter in each filter cycle

a) What flow rate (m 3/s) does the filter handle during production? b) What volume of water is needed for backwashing plus rising the filter in each filter cycle?

  Largest acceptable value of distance for removing a nail

To remove a nail, a small block of wood is placed under a crowbar, and a horizontal force P is applied as shown. Knowing that the maximum vertical force needed to extract the nail is 2600 N and that the horizontal force P is not to exceed 290 N, d..

  Determine the magnitude of the acceleration of point p

A wheel has an angular acceleration of alpha=(0.5*theta) rad/s^2 , where theta is in radians. a) Determine the magnitude of the velocity of point P located on its rim after the wheel has rotated 2 revolutions.

  Find the dimensions of an acceptable box of a largest area

a delivery company accepts only rectangular boxes the sum of whose length and girth (perimeter of a cross section) are equal to 108cm. find the dimensions of an acceptable box of a largest area.

  Freeways density and level of service

What will the freeway's density and level of service be before and after the ban? (Assume that the trucks are removed and all other traffic attributes are unchanged).

  Determine the minimum do concentration in the stream

A municipal WWTP discharges 22.5 MGD of secondary effluent containing 45 mg/L of ultimate BOD at 26.7 C with 1.3 mg/L of dissovled oxygen. The stream flow is 237 ft^3/s at an average velocity of 2.1 ft/s and an average depth of 7ft.

  Pore water pressure at failure

A CU triaxial test with σc = 20 psi is performed on a sand and a deviator stress of 80 psi fails the specimen. Previous tests revealed that the effective friction angle for this sand is 35°. Calculate the pore water pressure at failure.

  Calculate the final length and final diameter of specuman

A cylinder with a 6.0 in., diameter 12.0 in. height is put under a compresive load of 150 kips. The modulus of elasticity for this specimen is 8000 ksi and Poisson's ratio is 0.35. calculate the final length and the final diameter of this specuman..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd