Determine the variation of jet are with elevation

Assignment Help Civil Engineering
Reference no: EM13543375

1.A stream of liquid moving as low speed leaves a nozzle pointed directly downward. The velocity may be considered uniform across the nozzle exit and the effects of friction may be ignored. At a Nozzle exit the jet velocity and area are V and A, respectinely. Determine the variation of jet are with elevation.

2.Air at 400 kPa, 270 Kelvin, enters a well-insulated, horizontal pipe having a diameter of 2cm and exits at 90kPa, 200 Kelvin. Ideal gas model for air, determine at a steady state (a) The inlet and exit velocities, in m/s and (b) the mass flow rate, in kg/s

3.A 60 -m- long steel wire must not strech more than 48mm when the tension in the wire is 6 kn. Knowing that e-200GPa, determine (a)the smallestdiameter which may selected for the wire,(b)the corresponding value of the normal stress.

Reference no: EM13543375

Questions Cloud

Determine the lrfd nominal and adjusted design values : Problem: Determine the LRFD nominal and adjusted design values and adjusted design resistances for the following members and loading combinations. All members are Select Structural Southern Pine and are fully braced to prevent lateral torsional bucki..
Determine the adjusted asd values associated with the : Problem: A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D+S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.
Find the required minimum area for the heat transfer neglect : Saturated liquid water at 1000 kPa flows at 2 kg/s inside a 10 cm outer diameter steel pipe and outside of the pipe is a flow of hot gases at 1000 K with a convection coefficient of h = 150 W/m2 K
Determine the asd reference and adjusted design values for : Determine the ASD reference and adjusted design values for the following members and loading conditions. All members are Select Structural Southern Pine and are fully braced to prevent lateral torsional buckling. Bending Occurs about the strong axis.
Determine the variation of jet are with elevation : A 60 -m- long steel wire must not strech more than 48mm when the tension in the wire is 6 kn. Knowing that e-200GPa, determine (a)the smallestdiameter which may selected for the wire,(b)the corresponding value of the normal stress.
Historical treatment of children and juvenile justice system : Juvenile Delinquency, and the Interactive Module, "Historical Treatment of Children and Juvenile Justice System. "
How many tons of aggregate will be needed : The allowable stress in a steel shaft with an outside diameter of 1.5in and an inside diameter of 1.1in is 12,000psi. What hp can the shaft deliver at 1750rpm?
What is the maximum number of phases that may be present : For a ternary system, three components are present; temperature is also a variable. What is the maximum number of phases that may be present for a ternary system, assuming that pressure is held constant?
What is the maximum tension in the cable due to the 6-k load : Where should a single 500-lb live load be places on the beam so it causes the largest live moment at D? What is this moment? Assume the support at A is fixed, B is pinned, and C is a Roller

Reviews

Write a Review

Civil Engineering Questions & Answers

  Problem regarding helium balloons

To float a 160 pound man using helium balloons (assume 0.52 cubic feet per inflated balloon). How many balloons would it take? Assume density of air is 1.29 kg/cubic meter and the density of helium is 0.179 kg/cubic meter.

  How to select an appropriate w14 section

A 30 feet column is braced at the mid-section to prevent premature failure. If the maximum load is 380 kips, select an appropriate W14 section, if any, to support the loading conditions.

  Determine the momentum change of a person with a mass

Suppose that a person who boards the elevator on the ground floor gets off on the fifth floor. Assuming that the elevator has achieved operating speed by the time it reaches the second floor and that it is still moving at its operating speed as it..

  Dynamic viscosity of the liquid between the plates

The relative velocity of two infinitely wide parallel plates thatare 1cm apart is 10cm/s. If the dynamic viscosity of the liquid between the plates is 0.001 N s/m2 what is the shear stress between the plates?

  What is the equilibrium concentration of elemental mercury

Biota can uptake and bioconcentrate compounds through vapor phase absorption. For example, leaves exposed to elemental mercury vapors will absorb the mercury into the aqueous phase and the lipid phases of the leaves. Kow for mercury = 4.17.

  Determine what is the corrected length of the line

A 100ft tape is calibrated at 68 degrees F, fully supported with 15 Ibs of tension and found to be 99.987 ft long. Is this tape is used fully supported with 15 Ibs of tension at 86 degrees F to measure a distance that is recorded as 136.48 ft,

  What engineering parameter must the joint surfaces possess

The roadway is to be widened which will require a slope face cut at a steeper angle. Assume zero cohesion along the joints. What engineering parameter must the joint surfaces possess (magnitude) to be stable

  Highway practices abc-def-ghi are as follows

abc-def-ghi are as follows 060-001-120 ltbrgtneed it in 2 hours please send it to me as soon as

  Find the minimum dimension of the other side

The modulus of elasticity of the wood is 13GPa. If one side of the column is 25cm across, find the minimum dimension of the other side to keep the column's deformatin under 1.3 mm

  Determine the magnitude of force p acting on the crate

If the 50-kg crate starts from rest and travels a distance of 6m up the palne in 4s, determine the magnitude of force P acting on the crate. The coefficient of kinetic friction between the crate and the ground is \mu_k=.25

  Determine the flow rate per unit width of the auquifer

The potentiometric surface elevations at two observation wells 1000 m apart are 52.35 m and 56.90 m. If the horizontal hydraulic conductivity of the auquifer is 25 m/ day determine the flow rate per unit width of the auquifer.

  What total cylinder length l is required for the platform

The platform itself weights 30 kN in air, and each cylinder weighs 1.0 kN per meter of length. What total cylinder length L is required for the platform to float 1 m above the water surface

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd