Determine the values of theta dot and theta dot at instant

Assignment Help Civil Engineering
Reference no: EM13305766

The plate OAB forms an equilateral triangle which rotates counterclockwise with increasing speed about point O. If the normal and tangential components of acceleration of the centroid C at a certain instant are 80 m/s^2 and 30 m/s^2, respectively, determine the values of theta dot and theta dot dot at this same instant. The angle theta is the angle between line AB and the fixed horizontal axis.

Reference no: EM13305766

Questions Cloud

Determine the values of theta dot and theta dot at instant : The plate OAB forms an equilateral triangle which rotates counterclockwise with increasing speed about point O. If the normal and tangential components of acceleration of the centroid C
How much dividends were paid to shareholders during the year : How much in dividends were paid to shareholders during the year? Assume that all dividends declared were actually paid.
What is the gauge pressure in the truck : Water flows from a fire truck through a hose that is 10.7 cm in diameter and has a nozzle that is 2 cm in diameter. what is the gauge pressure in the truck
What was its charge fordepreciation and amortization : Income statement: Pearson Brothers recentlyreported an EBITDA of $7.5 million and net income of $1.8million. It had $2.0 million of interest expense, and itscorporate tax rate was 40%. What was its charge fordepreciation and amortization?
Determine the values of theta dot and theta dot at instant : The plate OAB forms an equilateral triangle which rotates counterclockwise with increasing speed about point O. If the normal and tangential components of acceleration of the centroid C
What would happen to the u.s. standard of living : What would happen to the U.S. standard of living if people lost faith in the safety of the financial institutions? Explain.
Compute the power output of the engine : An engine absorbs 1.69 kJ from a hot reservoir at 277 °C and expels 1.24 kJ to a cold reservoir at 27 °C in each cycle. What is the power output of the engine if each cycle lasts 0.298 s
Determine what is the mass of the particles collected : a stream f gas flowing at 3000 cfm has a particulate loading of 50gr/ft what is the allowable exit loading if 95 % collection efficiency is required. what is the mass of the particles collected
Calculate the energy transferred to the gas by heat : A 2.00-mol sample of hydrogen gas is heated at constant pressure from 302 K to 414 K. Calculate the energy transferred to the gas by heat

Reviews

Write a Review

Civil Engineering Questions & Answers

  Define two types of classifiers mostly used in data mining

Two types of Classifiers mostly used in Data mining. Other than Naive Bayes and decision trees, pick two other types of classifiers and discuss how they work

  Establishing a horizontal distance

A tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. What measurements should be laid out to establish a horizontal distance of 682.25ft?

  How far will the column of mercury in the tube be depressed

An open clean glass tube, having a diameter of 3 mm is inserted vertically into a dish of mercury at 20c .How far will the column of mercury (S.G =13.6) in the tube be depressed in (mm) given the following information. Theta = 130 and surface tens..

  What are the internal forces and moment at point a

Consider the two loading scenarios on the beam, where the beam is supported by a pin joint on the left and roller joint at the right end. What are the internal forces and moment at point A for each scenario

  Elevation and stationing of the low point

A 1600 ft long sag verical curve (equal tangent) has a pvc at station 1200+00 and elevation o 1500 ft. the initial grade is -3.5% and the final grade is 6.5%. determine the elevation and stationing of the low point, pvi and pvt.

  Determine the service rate for six vehicles per minute

Vehicles begin to arrive at a toll booth at eight vehicles per minute from 9 A.M. to 10 A.M. The booth opens at 9:10 A.M. and services at a rate of ten vehicles per minute until 9:40 A.M. From 9:40 A.M. until 10 A.M.

  Is crack width permissible assuming the exposure is dry air

Determine the estimated width of flexural cracks that will occur in the 8" (total depth) one-way slab shown in the figure below. Assume bottom clear cover is3/4". is the crack width permissible assuming the exposure is dry air

  Average waiting time in the queue

What is the average length of queue, the average time spent in the system, and the average waiting time in the queue?

  Explain plan for construction of a small child care center

describe how would you develop a subcontracting plan for the construction of a small child care center

  Compute the max possible moment at the centerline

compute the max possible moment at the centerline of the beam and the absolute moment in the beam.

  Explain how and why the rotational restraint at top of wall

The design of a masonry wall to support vertical compression loading is influenced by the same factors that affect the design of all compression elements. One of these factors is the extent of rotational restraint at the top of the wall.

  Parallel tangents of a reversed curve

The perpendicular distance between two parallel tangents of a reversed curve is 20m. The azimuth of the back tangents of the curve is 270 00 and the azimuth of the common tangent is 310.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd