User Account

All Pages

Determine the values of the constants

Assignment Help Mechanical Engineering
Reference no: EM13887027

The tensile stress-strain curve of a certain material is best represented by a satu- ration model, σ = σ o[1 - exp(- Aε)].

A. Derive an expression for the true strain at maximum load in terms of the constants A and σ o.

B. In a tension test, the maximum load occurred at an engineering strain of e = 21% and the tensile strength was 350 MPa.

Determine the values of the constants A and σ o for the material. [Remember that the tensile strength is the maximum engineering stress.]

Reference no: EM13887027

Questions Cloud

Identify the accounts that could contain misstatements : Identify the accounts that could contain misstatements, how the misstatements might occur, and how the auditor would adjust substantive audit procedures because of the material weakness.
Determining the true strain in the larger area : One part of the gauge section has an initial cross-sectional area that is 0.99 times that of the rest of the gauge section. What will be the true strain in the larger area after the smaller area necks and reduces to 50% of its original area?
Analysis of your assigned quantitative research design : Post 3- to 5-pages analysis of your assigned quantitative research design. Your analysis should include:  A brief description of the design and where it is most appropriately used and The assumptions for the design
What skills are required for any potential applicants? : What skills are required for any potential applicants? For example, what personal, behavior, or technical skills are desired?
Determine the values of the constants : Determine the values of the constants A and σ o for the material. [Remember that the tensile strength is the maximum engineering stress.]
Conduct a analysis and observation of specific sub-culture : In an essay of at least 1,500 words, please conduct a close analysis and observation of a specific sub-culture. The sub-culture you choose mustbe specific to ensure that you can sucessfully accomplish the essay
Determining the points on a stress-strain curve : Two points on a stress-strain curve for a material are σ = 278 MPa at ε = 0.08 and σ = 322 MPa at ε = 0.16. A. Find K and n in the power-law approximation and predict σ at ε = 0.20.
How auditing standards affect the design of audit programs : Describe how auditing standards affect the design of audit programs. What is an audit program? What information should an auditor gather before developing an audit program?
Values of engineering stress and strain : In a tension test, the following values of engineering stress and strain were found: s = 133.3 MPa at e = 0.05, s = 155.2 MPa at e = 0.10, and s = 166.3 MPa at e = 0.15.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 10 lb bag is pushed off a and swings in a verticle plane

a 10 lb bag is pushed off a and swings in a verticle plane and the end of rope l5. calculate and plot the swing of the

  Find the overall unweighted and a-weighted sound pressures

White noise has a constant level when measured in frequency bands of constant width. Suppose a noise generator produces white noise over the octave bands 0.5,1,2,4,8 khz. Find the overall unweighted and a-weighted sound pressures if a sound pressure ..

  Calculate the net entropy change of the system

A hollow steel sphere with .5 m inside diameter and a 2 mm thick wall contains water at 2 MPa, 250 C. The system (steel plus water) cools to the ambient temperature, 30 C. calculate the net entropy change of the system and surroundings for this proce..

  If the seat pocket diameter in a ball valve is 5000 the

if the seat pocket diameter in a ball valve is 5.000 the seat seal ring to ball sealing diameter is 4.438 and the

  Large plastic casting with thermal diffusivity

A large plastic casting with thermal diffusivity 6.0 x10^7 m2 /s is removed from its mold at a uniform temperature of 150 degrees C. The casting is then exposed to a high-velocity air stream such that the surface experiences a sudden change in temper..

  At each stage find pressure temperature specific volume

a solar-thermal power plant uses ideal rankine with r-134a. mass flowrate is 5000 kgs. the sat. vapor enters the

  Determine the kinetic energy of the bullet at the muzzle

A 168-grain bullet is accelerated in a 20 inch barrel and leaves the muzzle at 2800 ft/s. A) Determine the work done on the bullet by all external forces while the bullet is traveling in the barrel. B) Determine the kinetic energy of the bullet at th..

  Changes in kinetic and potential energies are negligible

Air is compressed steadily in a compressor from 100kPa and 300 K to 1 Mpa and 500 K. The compressor is not well insulated and a heat loss of 40 KJ/kg occurs during the process. Assuming the changes in kinetic and potential energies are negligible, de..

  Determine the strains in thick walled cylindrical vessel

Cylinder problem, Determine the strains in thick walled cylindrical vessel with inside diameter 1000 mm and outside diameter of 1400 mm

  Determine a the maximum temperature in the cycle the net

a four-cylinder four-stroke 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression

  The exhaust of each turbine is cooled to near saturated

a 1200 mwe pressurized water reactor pwr with an overall thermal efficiency of 30 is designed to supply saturated steam

  If the ball falls past him 075 s later determine the

a boy throws a ball straight up from the top of a 12m tower. if the ball falls past him 0.75 s later determine the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd