Determine the values and locations of the maximum tensile

Assignment Help Mechanical Engineering
Reference no: EM132319542

Federation University - ENGIN5302 Modelling & Simulation Project

Task 1 -

1588_figure1.png

The truss shown in Figure 1 is subjected to distributed load along the top left face and point loads at various intervals. Perform a finite element analysis of the truss using Abaqus. Your report should document the following results:

1. The deformed shape of the truss.

2. The stress contour of the truss.

3. The location of the maximum stress and maximum deflection.

Assume that all the members have a square cross section with sides b = 300 mm. The Young's modulus of the material used in the construction of the truss is E = 210 GPa.

In your finite element analysis, use the following:

1. Linear beam element in Abaqus.

2. Perform a convergence study by increasing the number of elements along each member of the trus. You may try to use 2, 4, 8, 16 elements per member, compare and report your observations.

3. Use line load when applying the distributed load w.

Task 2 -

A concrete overpass structure is shown in the figure below. Assume plane strain condition. Let Young's modulus E = 900 kPa and Poisson's ratio v = 0.2. Determine the values and locations of the maximum tensile and compressive principle stresses occurring in the slope model. Determine also the abslolute maximum displacement magnitude and its location experienced by the slope model. The boundary conditions of the slope model is as follows:

1. The left and right edges are constrained in the horizontal direction.

2. The bottom edge is constrained in both horizontal and vertical directions.

Considerable amount of experience is necessary to select an "optimal" mesh so that the results are sufficiently accurate for engineering purposes at the minimum amount of computational cost. Very often, calculations with a series of meshes starting from a coarse one need to be performed, and their results compared. In this task, you are required to follow the "best-practice" modelling approach. This analysis consist of two parts.

Part 1 - The simplest approach is to rene the mesh uniformly. Start with a coarse mesh by specifying a global seed size hseed = 20 m. Use 4-node quadrilateral elements with mapped feature turned off i.e. use free meshing. When specifying element type, turn off the reduced integration option. Perform a finite element analysis using this mesh and record the results. Then repeat the analysis by specifying a smaller global element sizes hseed = 10 m, 5 m, and 2.5 m. Report on the observations you make with regards to the stress contour, and the value of the maximum tensile and compressive stresses.

You may need to consult the user's manual or the tutorial examples to complete the finite element analyses. A convergence study is to be performed for each of the required values. This study will lead to "best estimates" and error estimations to these values. The aim of this task is to exercise the "best-practice" approach in finite element analysis. It is unacceptable to perform the computation with one fine mesh only.

Part 2 - Compare the quality of 3-node triangular, 6-node triangular, 4-node quadrilateral and 8-node quadrilateral elements. To evaluate the quality of different types of elements, meshes with similar numbers of nodes are generated using each type of element. An element of higher quality will lead to more accurate results. In this part of the task, you will repeat the analysis in Part 1 using hseed = 5 m. Assume that the result obtained with hseed = 2.5 m in Part 1 is accurate enough and will be used as a reference solution. The finite element results from the four different elements (3-node triangular, 6-node triangular, 4-node quadrilateral and 8- node quadrilateral) will be compared with this reference solution. Rank the performance of the elements according to their accuracy. Comment on the observations you made.

451_figure2.png

Report - Your report should include the following key contents:

1. Title page

2. Table of contents

3. Brief description of objective of analysis

4. Description of the methodology which includes

(a) The steps/algorithms of calculations

(b) Description of mesh

5. Analysis results, evaluations and discussion

(a) Plot of the finite element mesh

(b) Contour plot of displacements

(c) Contour plot of stresses

(d) Tabulated displacements and stresses at required locations

(e) Estimation for errors based on a convergence study

6. Conclusions (best estimates of displacement and stresses, error estimation, etc.) and suggestion for further improvement in your analysis.

Note - Make report using Abacus.

Reference no: EM132319542

Questions Cloud

Proposed plan for integrating all of the strategic technique : Develop a PowerPoint presentation of 8-11 slides for a proposal, including 200-250 words of speaker notes per slide - describe concept applications in detail
What is the total budgeted compensation for both : The current audit bid for Monoco Industries requires $18,000 in direct partner professional labor, $30,000 in direct staff accountant professional labor.
Find the cost per unit of conversion activity is : Lakeland Chemical manufactures a product called Zing. Direct materials are added at the beginning of the process, and conversion activity occurs uniformly.
Develop a deep familiarisation with its properties : This exercise involves you working with an already acquired dataset to undertake the remaining three key steps of examining, transforming and exploring.
Determine the values and locations of the maximum tensile : Federation University - ENGIN5302 Modelling & Simulation Project. Determine the values and locations of the maximum tensile
Describe the relationship between the two types of failures : Our textbook points out that the most important failure for the events of 9/11 was that of imagination, and that the failure during Hurricane Katrina was one.
According to neoclassical theory of the firm : According to neoclassical theory of the firm, why, under perfect competition, will firms choose the level of output where the marginal cost of a unit equals
Terms of practical implementation : Your understanding of why the RBA made the June 2019 decision that they did, with respect to the content of the interest rate decision statement itself
Capital gain tax regarding historical sculpture : Discuss Barbaras income under the case scenario - Discuss the effect of these arrangement on the assessable income of Patrick

Reviews

len2319542

6/10/2019 4:01:50 AM

Note - Make report using Abacus, Additional remarks - This assignment contributes to 30% of the total assessment of this course. Submit an electronic copy via Moodle. You are allowed to work alone or in a group of two individuals. Two is the limit. This is non-negotiable.

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd