Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
PSpice Use the values of C and L determined in Problem 30 to input the circuit of Figure 21-70. Repeat the measurements of
Problem 35.
Problem 35
PSpice Use the values of C and L determined in Problem 29 to input the circuit of Figure 21-69. Use the Probe postprocessor to display the response of the capacitor voltage as a function of frequency. From the display, determine the maximum rms voltage, the resonant frequency, the half-power frequencies, and the bandwidth. Use the results to determine the quality factor of the circuit.
Problem 29
Refer to the circuit of Figure 21-69.
a. Determine the value of XL for resonance.
b. Solve for the Q of the circuit.
c. If the circuit has a resonant frequency of 2000 rad/s, what is the bandwidth of the circuit?
d. What must be the values of C and L for the circuit to be resonant at 2000 rad/s?
e. Calculate the voltage VC at resonance.
What assembly language instruction sequence would be used to configure an internal CPU register to access an array, named TABLE, that starts at memory location $1000. Write the assembly language instructions below a programmer could use to copy.
A 1000/5 A currenttransformer bar primary type has the loss component of excitingcurrent equal to 0.7% of the primary current. Find the ratio error(i) when the turn's ratio is equal to normal ratio (ii) when the secondary turn is reduced by 0.5%.
A new type of Schottky diode is optimized for low-voltage applications. It has typical forward voltage drop of 0.2 V, but its leakage current can be as high as 80 mA. It is being considered for a 12 V to 2.5 V converter with 50 W load.
(a) find the value of a and K so that the relative damping ratio of the system is 0.5 and the rise time step response is approximately 1 s. (b) with the values of a and k found in previous question
Compute numerically and plot the average power as a function of the target rate for different L to get a sense of the amount of gain from having multiple receive antennas. Qualitatively describe the nature of the performance gain.
FPGAs are programmed from acompiled HDL description (i.e., a Verilog or VHDL program). What would you have to have in the HDL description to use the globalset/reset function in the Spartan FPGA
What 3 variables does ohms law take into account? (Electricity question)
Assume that a load Z absorbs power of 150W at a lagging power factor of 0.8, and the voltage across the load Z is 220Vrms, 50 Hz. What must be the value of capacitor that needs to be connected in parallel with the load Z
Why radio waves are chosen for Remote & close range transmission? and how HOW TO CONSTRUCT A SIMPLE RADIO RECEIVER ?
A 4157-V rms, 3-phase supply is applied to a balanced Y-connected three-phase load consisting of three identical impedances of 48 at angle 36.87 degrees . Taking the phase voltage Van as reference
Slots in the broad wall of a rectangular waveguide scatter power symmetrically, so that they can be modeled as a shunt admittance,Y, in a transmission line. Consider the waveguide structure below, with four equally space slots .68 lambda apart
Consider a direct sequence spread spectrum (DSSS) system attempting to transfer data. The DSSS system has a data rate of 2 Kbps (2 thousand bits/sec) which is spread to 2 Mcps
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd