User Account

All Pages

Determine the value of steady state error

Assignment Help Electrical Engineering
Reference no: EM13871271

The transfer function of  second order  system is given by And its input is given by r(t)=25t u(t).

447_123.png

Required.

i. Show that the response is able to follow the input with a steady state delay of 
ii. Determine the value of steady-state error 60m/s.

 

Reference no: EM13871271

Questions Cloud

Prepare the journal entries to record the transactions : Lets go a bit further with the example from M8-3. Assume that on February 2, 2015, Extreme Fitness received a payment of $ 500 from one of the customers whose balance had been written off. Prepare the journal entries to record this transaction.
Moneybaggs hires you as her financial consultant : Moneybaggs hires you as her financial consultant How will you advise her?
Raise the temperture of an object with a heat capacity : How much heat is required to raise the temperture of an object with a heat capacity of 3.4 j/k from 17.34 k to 67.18k?
Is an operating statement prepared for an agency fund : Is an operating statement prepared for an Agency Fund? Why or why not?
Determine the value of steady state error : Show that the response is able to follow the input with a steady state delay of Determine the value of steady-state error 60m/s.
Estimate the n-h bond energy in nh3(g) : 1.The enthalpy change for the following reaction is -903 kJ. Using bond energies, estimate the N-H bond energy in NH3(g). 4NH3(g) + 5O2(g)4NO(g) + 6H2O(g)
Define an agency relationship : Define an agency relationship.
Write offs and bad debt expense using the allowance method : Recording Write-Offs and Bad Debt Expense Using the Allowance Method Prepare journal entries for each transaction listed. a. At the end of June, bad debt expense is estimated to be $ 14,000. b. In July, customer balances are written off in the amount..
How are private purpose trust funds controlled : How are Private Purpose Trust Funds controlled?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  The voltage at a point between p and q and 50m from p

A 2-wire DC distributor PQ is 500m long. It is supplied by three feeders entering P, Q and R where R is midway between P and Q. the resistance of the distributor, go and return, is 0.5W/km.

  How to trace that when both jk flip flops depend on input

but the K input of the second JK flip flop depends on the negated output of the first JK flip flop and x AND together. How to trace that when both JK flip flops depend on input from the other one

  Construct required circuit with min number of unit transistr

Assuming that only integer multiples of a unit bipolar transistor having IS = 3 x 10-16A can be placed in parallel, and only a single voltage source, VB, is available (Fig. 4.54), construct the required circuit with minimum number of unit transist..

  Design a circuit to compute f and ignore overflow issues

Design a circuit to compute F = (A*B*C) +3*D+12. where A,B,C and Dare 16-bit inputs, and F is a 16-bit output. Use 16-bit multiplier and adder components, and ignore overflow issues.

  Design a full-wave rectifier to provide a dc output

Design a full-wave rectifier to provide a dc output of 28V at a current of 4A, with a ripple of not more than 3%. A linevoltage of 120V (rms), 60Hz is available.

  What is the difficulty with the original tcp srtt estimator

In the absence of any special knowledge of network conditions, the typical approach is to pick an arbitrary value, such as 3 s, and hope that this will converge quickly to an accurate value. If this estimate is too small, TCP will perform unnecess..

  Determine poles and zeros and gain for the analogue filter

In this section the linear phase constraint will be dropped, and a magnitude only design sought for the low-pass filter using the bilinear transform of Butterworth and Elliptic analog prototypes. The steps are (a). Decide on an analog prototy..

  Find what are the worst-case and the average errors

Suppose you have an Analog-to-Digital Converter (or ADC) with 12 bits of precision, and the manufacturer claims it has the transfer function x = floor(4096×v/5 ) for input voltage vΣ [0, 4.9999] (where x is the digitized result you get).

  Calculate the output noise power and noise voltage

A three-stage amplifier is shown. The operating bandwidth is 500 KHz at a temperature od 25 degrees C. The output load is 1000 ohms. calculate the total NF as a number, calculate the output noise power, and calculate the output noise voltage.

  Determine the steady state output voltage in the circuit

If the circuit is driving a 100Ω load with a signal generator that has an output impedance of 50Ω and an open-circuit output voltage of .5sin(500t+30º), determine the steady state output voltage.

  Solve the equation and the basic definitions

Solve the equation z^2+z+1=0 using z=(x,y) and the basic definitions. (Hint: Note that y does not equal 0 because the equation X^2+X+1 does not equal 0 for any real number x.)

  How much heat q is absorbed by water from heating resistor

The amount of heat Q needed to turn a mass, m, of room temperature ( T_1) water into steam at 100 Celcius. ( T_2) can be found using the specific heat, c, of water and the heat of vaporization, H_v, of water at 1 atmosphere of pressure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd