Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Draw a diagram consisting of a potential block with the following characteristics:
Region I: X< 0 V=0Region II: X=0 to X= a V=VoRegion III: X>0 V=0
(a) Determine the wave equations for all three regions.(b) What is K for each region(c) Perform BC at X=0 and X=a(d) Using matrix algebra, determine the coefficients to the wave equation in Region II(e) Determine the transmission coefficient for the system for X=a where a is on the order of nanometers(f) Determine the transmission coefficient for the system for X=a where a is on the order of meters
For the given circuit, determine the function of it I.e. is it OR gate? Or AND gate,.. Show all your answer, also draw the symbol and truth table of it.
An LED is rated at VF = 1.6 Volts to 2.0 Volts at IF = 20 mA. What value of series resistance is needed to limit the LED current to 20 mA when this LED is connected to a 32 Volts peak source
Air Enters a cooling section at 97Kpa, 35C and 30 percent relative humidity at a rate of 6m^3/min, where it is cooled until the moisture in the air starts condensing. Determine the temperature of the air at the exit and the rate of heat transfer i..
The (uniform) area density of defects for a CMOS fabrication process is 0.1 cm-2. Estimate the yield for integrated circuits with the following dimension: 4mm x 4mm, 6mm x 8mm, and 9mm x 12mm.
To develop contoller as a sequential circuit using minimum number of D flip-flops and the minimum number of external gates. the controller should set the values of the control lines appropriately to drive the combinational logic circuit.
when the line was open-circuited, the measurement yielded an input impedance equivalent to a capacitor with capacitance of 40 pF. Find Zo of line, the phase velocity, and the relative permittivity of the insulating material.
A beam of X-rays with a wavelength l of 0.15 nm is directed at a crystal whose planes have a spacing of 0.25 nm. How many diffraction peaks (each arising from a different order n) are possible
PAL12H6 (12 inputs, 6 outputs, AND-OR structure, two output OR's have 4 AND gate inputs and four output OR's have 2 AND gate inputs). NOTE: you need to show only appropriate product terms used for PAL implementation
A shunt DC motor has RA = 0.7-ohm and VT =429.6 V. For an output power of 50.4 hp, we have nm = 1,452 rpm and IA = 110.8 A. The field current remains constant for all parts of this problem. Find the rotational power loss in watts.
Explain the relationship between the input and the output ac signals for a n-channel BJT voltage-divider bias. What components/parameters does the voltage gain depends on
specify the parameters Rin, Avo, and Ro of an amplifier that is to be connected between a 100k ohm source and a 2k ohm load and is required to meet the following specifications: A. No more than 10% of the signal strength is lost in the connection t..
Two one phase loads, a 5kW resistor, and a 10kVA load with a 0.707 lagging power factor are connected in parallel to a 120 V source. What is The power factor of the current supplied to the two loads by the source
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd