Determine the transfer function of the second-order lpf

Assignment Help Electrical Engineering
Reference no: EM13285024

Determine the transfer function of the second-order (2 poles) lowpass Butterworth filter with a 3-dB cutoff frequency of 5 kHz. Design it using the Sallen-Key lowpass filter configuration, find all the values of the circuit elements, and draw the circuit. What is the DC gain?

Reference no: EM13285024

Questions Cloud

Taylor series expansion : Key constraints in your computer program are that I expect the code to evaluate Pn(x), for a given x, to be in its own subroutine and that Horner's algorithm (page 90, algorithm 2.7) is used to evaluate Pn(x).
What is magnitude of the electric field at center of loop : A long, thin, nonconducting plastic rod is bent into a circular loop that has a radius a. Between the ends of the rod a short gap of length l, where l
Explain the ka for hypochlorous acid (hclo) : The Ka for hypochlorous acid (HClO) is 3.0 x 10?8. What is [OH?] in a 0.145 M solution of sodium hypochlorite (NaClO)
Effective public health tools in outbreak of tuberculosis : What has been found to be effective public health tools in dealing with an outbreak of tuberculosis (TB) Whooping Cough, HIV/AIDS? What has been found to be effective tools in dealing with marlaria, Dengue Fever and other mosquito borne disease?
Determine the transfer function of the second-order lpf : Determine the transfer function of the second-order (2 poles) lowpass Butterworth filter with a 3-dB cutoff frequency of 5 kHz. Design it using the Sallen-Key lowpass filter configuration,
What is the maximum height of the stadium : Ted Williams hits a baseball with an initial velocity of 120 miles per hour (176 ft/s) at an angle of ? = 35 degrees to the horizontal. what is the maximum height of the stadium
Explain what is the percent dissociation of (ch3)2nh : Dimethylamine, (CH3)2NH, is a weak base ( Kb = 5.4 x 10?4). What is the pH of a 0.50 M solution and what is the percent dissociation
Draw a mod-10 johnson counter using d-bistables : 1. Design a synchronous Mod-10 up counter from 1st principles nusing K-MAPS. Use Diagram 1(insert answer book) and also draw the final counter in your book. 2. Draw a MOD-10(5-bit) Johnson counter using D-bistables.
What was the carts initial speed : A wheeled cart is shoved up an inclined plane with an unknown initial speed. What was the cart's initial speed

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the armature current and speed

A 300 V, 60 A, 1200 rpm series dc motor has an armature and series field resistance of .2 ohms each. When a .10 ohm resistance is connected in parallel to the winding, the motor's torque is doubled.

  Calculate the series impedance and the shunt admittance

A 300-km bundled 500-kV, 60-Hz, three-phase completely transposed overhead line has three ACSR 1351-kcmil conductors per bundle, with the bundle spacing 0.5 m. The horizontal phase spacings between bundle centers are 10, 10, and 20 m.

  Calculate distance of first voltage min point to the load

A transmission line with characteristic impedance Z0= 60 ohms is connected to a load impedance ZL= 40-j20 ohms. The wavelength is 8 cm. A. Calculate the load reflection coefficient. B. Calculate the voltage standing wave ratio C.

  Determine what is the angle of the middle one

Unpolarized light is incident on three polarizers: The first making an angle of 0 degrees with the vertical; the second making an angle of ? degrees with the vertical; and the last one making an angle of 90 degrees with the vertical.

  Determine the minimum double-sided nyquist bandwidth

For a 64-PSK modulator with an input data rate(fb) equal to 36 Mbps and a carrier frequency of 100 MHz. A. Determine the minimum double-sided Nyquist bandwidth(fN) and the baud. B. Sketch the output spectrum.

  What is about whether the power and reactive are positive

Given that a nonzero AC voltage source is applied, what can you say about whether the power, reactive and complex power are positive,negative, or zero for: A) a pure capacitor in series with a pure inductor.

  What is value of the feedback resistor require for amplifier

A pressure sensor covers a range of 0-500 psi with 2.5 mV/psi. The sensor is input to an ADC with a voltage range of 0 to 5 V. What is the value of the feedback resistor required for a non-inverting amplifier circuit required to interface the sens..

  Determine rotor speed and rotor frequency of induction motor

A 100 hp, 16 pole, 460V, three phase, 60hz induction motor has a slip of 2.4 percent when running at rated conditions. Determine (a) synchronous speed; (b) rotor speed (c) rotor frequency.

  Find how much charge moves through the element

Over a period of 10 seconds, how much charge moves through the element. If electrons carry the charge, which terminal do they enter. How much energy os transferred. Is it delevired to the element or taken from it.

  What is the total impeadance of the combined three loads

Three loads are connected in parrallel across a 250 Vrms line. Load 1 absorbs 16 kW and 18 kVAR. Load 2 absorbs 10 kVA with a power factor of 0.6 leading. Load 3 absorbs 8 kW with a power factor of 1.

  What is the difference between the wavelengths

isible light passes through a diffraction grating that has 900 slits per centimeter, and the interference pattern is observed on a screen that is 2.58 m from the grating. In the first-order spectrum, maxima for two different wavelengths are separat..

  Determine magnitude of the average inductor current

A buck-boost converter works with an input voltage of 12 V and switching frequency 10 kHz. The load resistance of 24 Ω requires doubled input voltage. The inductor and capacitors are 1 mH and 100 μF, respectively.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd