Determine the total solids in the sample

Assignment Help Civil Engineering
Reference no: EM13323462

A surface water sample has been evaporated until dry in a crucible dish. The dry (tare) weight of the crucible is 44.642gm. The weight of the residue plus the cruciible is 44.6484gm. Determine the total solids (both dissolved and suspended) in the sample if the sample volume was 10 mL.

Reference no: EM13323462

Questions Cloud

What is the temperature change of the air : An indoor swimming pool of depth 2m transfers heat at a rate of 100w/m2 to the 10m of air between the pool and the roof for 1000s. What is the temperature change of the air
What is the specific discharge in the rectangular channel : A large concrete channel holds a hydraulic jump in which the subcritical depth of flow is 2.5 m. If 40 percent of the specific energy in the flow is lost through the hydraulic jump, what is the specific discharge in this rectangular channel
Divide the sodium hydroxidecharge into 10 smaller charges : Divide the sodium hydroxidecharge into 10 smaller charges, and add them one at a time, makingsure that each is well mixed and the tank temperature has stoppedincreasing before adding the next charge.
Find acceleration and direction of the motion of the system : 3 objects are connected on an inclined table with the masses of 8.0kg, 4.0kg and 2.0kg and the pulleys are frictionless. determine the acceleration and direction of the motion of the system
Determine the total solids in the sample : A surface water sample has been evaporated until dry in a crucible dish. The dry (tare) weight of the crucible is 44.642gm. The weight of the residue plus the cruciible is 44.6484gm.
Explain the delta h for the neutralization of naoh : The delta H for the neutralization of NaOH with H2SO4 is -144kj/mol H2SO4. What is the maximum measured temperature in the styrofoam cup
Determine the required bolt spacing in the longitudinal x : A 10 m long built-up beam is to be fabricated from a universal section beam (UB) and two 'C' channel sections (as indicated). The beams are joined by bolts, with the allowable shear load in each bolt being 12 kN.
What frequency would be required : If a 2.4 m wave was created using a frequency of 63 Hz, what frequency would be required to creat the next higher harmonic
How to determine the two possible depths of flow : A 200 m wide natural stream, whose cross-section can be approximated by a rectangular cross-section, contains a dischargeof 80 cumecs. If the specific energy of the flow is 1.5 timesthe minimum specific energy

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the point at which the line with parametric equation

Find the point at which the line with parametric equation x=2+3t, y=-4t, z=5+t intersects the plane 4x+5y-2z=18

  What is elevation of b by neglecting curvature and reaction

The line of sight of a level falls at a rate if 0.122ft/ 100 ft when the level bubble is centered. A backsight of 4.782 is taken on point A, which is at 75 ft from the level. the elevation of a is 425.238 ft.

  Estimate the constant rate of withdrawal from reservoir

Estimate the constant rate of withdrawal (in m^3/s) from a 1375 ha reservoir in a month of 30 days during which the reservoir level dropped by 0.75 m in spite of an average inflow into the reservoir of 0.5 Mm^3/day.

  Draw a small sketch that shows a situation

Name three types of metamorphic foliations, and draw a small sketch that shows a situation where a metamorphic foliation could cause problems in an excavation.

  Calculate the power input to the pump in kw

A 60 MW Rankine steam power cycle in Iceland uses reheat. The system is comprised of a single adiabatic pump, a boiler using geothermal energy, two adiabatic turbine stages and a condenser.

  Determine thermal efficiency and mass flow rate of cooling

A simple steam power plant operates at steady state with water circulating through the components with a mass flow rate of 100 kg/s. Stray heat transfer, kinetic energy and potential energy effects are negligible.

  What is loss in truck operating cost for the logging company

The performance functions of these three routes are: t1=50+0.2v1, t2=80+0.1v2, t3=120 + 0.05v3 t1, t2, t3 and are travel times in minutes; v1, v2, v3 are flows in number of trucks per day.

  Find the pressure considering both friction and minor losses

Water flows through a 200 m long ,30 cm diameter steel pipe with surface roughness 0.046 mm at a rate of 0.25 m^3/s .Find the pressure(P2)considering both friction and minor losses

  Will the quality of the coarse aggregate increase

To adjust the mix so as to increase the compressive strength, the water-to-cement ratio is reduced to 0.45. Will the quality of the coarse aggregate increase, decrease, or stay the same

  Determine what is the hydraulic conductivity of the sand

it was observed that the quantity of the water flowing through the sand layer into the collection ditch is 250 m^3/day. What is the hydraulic conductivity of the sand (k)

  Determine peak discharge if unit hydrograph is triangular

A hydrograph has a uniform rainfall intensity of 1.5 in/hr in the first hour, 2.0 in/hr in the second, and 0.75 in/hr in the third hour. Direct runoff (in inches) using the SCS method is 1.2in.

  Draw a footing detail showing all pertinent design parameter

design a square individual footing to support a 16 inch square reinforced concrete column. service loads include a dead load of 180 kips and a live load of 140 kips. both column and footing have fc=3000psi and fy=60000 psi.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd