Determine the time when they pass each other

Assignment Help Civil Engineering
Reference no: EM13563868

A motorcycle starts from rest at t = 0 and travels along a straight road with a constant acceleration of 4ft/s^2 until it reaches a speed of 50ft/s . Afterwards it maintains this speed. Also, when t = 0, a car located 8000ft down the road is traveling toward the motorcycle at a constant speed of 40ft/s .

a) Determine the time when they pass each other.

b)Determine the distance traveled by the motorcycle when they pass each other. please show work.

Reference no: EM13563868

Questions Cloud

How many years would it take for money to triple in value at : How many years would it take for money to triple in value at 20% per year simple interest? Please be descriptive on where the numbers and formulas comes from.
Determine the maximum load p that the member can support : A stainless steel tube with an outside diameter of 59 mm and a wall thickness of 5 mm is used as a compression member. If the axial normal stress in the member must be limited to 220 MPa, determine the maximum load P that the member can support.
How long will the generator run on a tankful of fuel : A Bonda portable generator is powering a small travelling fridge (120V) in your RV and consumes 125 watts. The efficiency of the generator's gas motor is 23% and the electrical portion (power head) is more efficient at 91%. If white gas weighs 6.073 ..
Calculate rocket position velocity and accelaration : To calculate a rocket’s position, velocity, and acceleration at different points in time. A rocket, initially at rest on the ground, accelerates straight upward with a constant acceleration of 58.8m/s^2
Determine the time when they pass each other : A motorcycle starts from rest at t = 0 and travels along a straight road with a constant acceleration of 4ft/s^2 until it reaches a speed of 50ft/s . Afterwards it maintains this speed. Also, when t = 0, a car located 8000ft down the road is travelin..
What will the cars maximum acceleration rate be under these : A 3000-lb car is traveling on a paved road with Cd (coefficient of drag) = 0.35, Af (frontal area of the vehicle) = 21ft^2, and p(air density)=0.002378 slugs/ft^3. Its engine is running at 3000rpm and is producing 250ft-lb of torque.
What will be the population in the year 2050 : A very small country has just gained independence in the year 2000, at which time its population was 1,000. The new country has a birth rate of 0.02 yr-1, death rate of 0.004 yr-1, immigration rate of 0.01 yr-1, and emigration rate of 0.005
How many resistors out of a package of 100 would you expect : Water is pumped 9 mi from a reservoir at elevation 100 ft to a second reservoir at elevation 210 ft. The pipeline connecting the reservoirs has a 54-in diameter. It is concrete and has an absolute roughness of 0.003. If the flow is 25 mgd and pumping..
Determine the velocity and position of point : Over a long period, total phosphorus (TP) has been discharged to a lake through sewage and surface water runoff at a rate of 10 tons/day. Measures were then taken to reduce the TP load to 1 ton/day. Assume that TP decays by a first order process with..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the modulus of elasticity of concrete by the aci

Determine the Modulus of Elasticity of Concrete by the ACI formula for a concrete cylinder that has a unit weight of 120pcf (1920kg/m^3) and a compressive strength of 3000 psi (21MPa).

  How many watts of power would it take to heat 1 l of water

How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h? Assume no heat losses occur, so all of the energy expneded goes into heating the water.

  Write a paper on steel sustainability - how to do design

write a paper on steel sustainability. - how to do design calculations for penthouse in steel building and- why the

  Determine the vertical force p exerted by the tower on pin a

a transmission tower is held my three guy wires attached to a pin at A and anchored by bolts b c and d if the tension in wire ab is 3.6 kn determine the vertical force p exerted by the tower on the pin at A

  How many particles would be present in a cubic meter of

How many particles would be present in a cubic meter of aerosol at the concentration of the U.S. PM-10 standard or 50 micrograms/cubic meter if the particles are .1 micrometer in diameter.

  Describe realistic investment problem for none of choice

Assuming we are still in a world with only discrete investment choice, i.e., option A, option B, etc., describe a realistic investment problem where none of the environments discussed apply without some reframing.

  Estimate the theoretical production of landfill gas

estimate the theoretical production of landfill gas (CH4 only) from the degradation of 20.3 kg of rapidly decomposable MSW. asssume the density of methane is 0.7177 kg/m^3.

  Determine elevation and stationing of high point pvc and pvt

a 520 ft long equal tangent crest vertical curve connects tangents that intersect at station 340 00 and elevation 1325 ft the initial grade is if 4 and the final grade is 2.5.

  Calculate the ph of the solution

A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10-4.

  Determine the factor of safety of this trench by the culman

A 1.5 meter deep vertical wall trench is to be cut in a soil whose unit weight is 17.36 kN/cubic meters, angle of internal friction is 25 degrees, and cohesion is 20.6 kN/square meters. Determine the factor of safety of this trench by the Culmann Met..

  Determine from first principles

At a section in a beam the tensile stress due to bending is 70 N/mm2 and there is a shear stress of 25 N/mm2. Determine from first principles, the magnitude and direction of the principal stresses

  Determine the magnitude and direction of the components

The beam is subjected to a force F=825 lb in the direction, and is supported by a pin connection at point B and a rope attached through a pin connection at point A. Problem #1: Draw a complete FBD of the beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd