Determine the time response of the microphone

Assignment Help Other Engineering
Reference no: EM131079643

1. Use Simulink or any other software to determine the time response of the microphone with τl= τ = 1 sec, ωn = 1500 Hz, ζ = 0.5 and K=2.5 due to the sonic boom pressure of FIGURE 6.47. Does this device give a good reproduction of the signal? Is this a practical microphone? Why?

18_Figure.png

2. If, in the system shown in Fig. 7.17, the amplifier tag is not neglected, so that (i/ee) (D) = Ka/[(τ1D + 1) (τ2 D + 1)], find the value of Ka that will put the feedback system just on the margin of instability (use the Routh criterion). If τ = 0.001 s and τ1 = τ2 = 0.000001, what is the maximum allowable value of Kb Ka Ke/Im for marginal stability? If a value of Kb Ka Ke/Im about one-fifth of that giving marginal stability can be used and if Eq. (7.43) is assumed applicable under these conditions, what percentage improvement of τct as compared with τ may he achieved?

1931_Figure1.png

The block diagram of Fig. 7.17 embodies the above relations, which may now be manipulated to give the relation between input v and output, eo:

((Keeo/Rro)+ Kv)((1/Im)(-KbKaRro)/τD+1) = eo              (7.41)

This gives finally

 eo/v(D) = (KctctD+1)                                                 (7.42)

where  τct =Δ  τ/1+ KeKbKa/Im                                      (7.43)

and Kct =Δ ((-KKbKaRro/Im)/(1+KeKbKa/Im))                 (7.44)

3. Perform a dynamic analysis on the system of Fig, 7,47a to obtain the transfer function relating fluid density as an input to strain-gage bridge voltage as an output. What is the effect of changes in liquid level in the still well on the output signal? What is the effect of thermal (volume) expansion of the float? If the entire assembly is aboard a vehicle that is accelerating vertically, explain the effect on the output.

153_Figure2.png

4. A thermometer is to have a sensitivity of 10 in/oC when mercury is used in the neighborhood of room temperature. Obtain an expression relating capillary cross-section area and bulb volume to meet this requirement. Obtain expressions for the time constant if the bulb is spherical and, if it is cylindrical with a length equal to 5 diameters. Also find the ratio of these two time constants.

5. A resistance-thermometer circuit as in Fig. 8.21d has R1 = R2 = 1000 Ω and is to cover the temperature range 0 to 400oC. The thermometer element is platinum with a resistance of 1,000 Ω at 200oC. Plot the curve of bridge output voltage (open circuit) versus input temperature, using the data of Fig. 8.19. Sec Chap. 10 for bridge-circuit equations. Bridge excitation is 20 V.

2122_Figure3.png

1498_Figure4.png

Reference no: EM131079643

Questions Cloud

Calculate official unemployment rate to second decimal place : Suppose the number of officially classified employed persons equals 80 million people; the number of discouraged workers is 12 million people; the number of stay at home spouses is 15 million people;  Based on this information, calculate the official..
Determine i1(t) for t > 0 for a constant applied voltage e0 : Determine i1(t) for t > 0 for a constant applied voltage E0 = 10 V.
Solve for t=0 the following differential equations : solve for t≥0 the following differential equations
Source of demand in the foreign currency exchange market : In open economy, what is the source of demand in the foreign currency exchange market?
Determine the time response of the microphone : Use Simulink or any other software to determine the time response of the microphone with τl= τ = 1 sec, ωn = 1500 Hz, ζ = 0.5 and K=2.5 due to the sonic boom pressure of FIGURE 6.47. Does this device give a good reproduction of the signal? Is this ..
Minimum average cost is referred to as the capacity of firm : The point of minimum average cost is referred to as the capacity of the firm. Yet we draw the average cost curve extending both to the left and to the right of this point. The firm can operate below capacity, but how can a firm operate above capacity..
Demonstrate familiarity with the concept of relevant costs : Demonstrate familiarity with the concept of relevant costs. Write 2-4 pages, showing computations and discussing the results. List supporting references and cite sources.
Deduce that the system of difference equations : Deduce that the system of difference equations
What is the present worth of the electric vehicle program : The US Department of Transportation has decided to invest in electric vehicles over the next 10 years. They will fund $0.5 million in year 1, $2 million in year 2, $3.5 million in year 3, $5 million in year 4 and $6.5 million each year thereafter. Gi..

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd