Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Two men are sliding a 100-kg crate up an incline. If the lower man pushes horizontally with a force of 500 N, and if the coefficient of static friction is 0.30, determine the tension T which the upper man must exert on the rope to get the crate to start moving up the hill.
design a 4th order Butterworth band-pass filter, using a low-pass filter followed by a high-pass filter, to extract the 1200Hz and 1500Hz components from the signal x(t) a. Determine the cut-off frequencies of the low-pass and the high-pass filters..
1) in a swamped common-emiter BJT amplifier, as shown below, if Vcc =12 V, R1 =8.2 kohm, R2=10 kohm, Rc = 500 ohm, Re= 1 kohm, Vbe = 0.7 V, and B =100, what is the transistor`s emitter current
Charges +Q and +3Q are seperated by a distance 2m. A third charge is located such that the electrostatic system is in equilibrium. Find the location and the value of the third charger in terms of Q.
Six input voltage sources (V1, V2, V3, V4, V5, V6) have a +/- 1 V range. Design a circuit to produce Vout as the most negative (smallest) of (V1 + 2V2), (V3 - 2V4), (-V5 - 2V6). Your design should specify exact components. Note that diode drop can..
In class we saw an example of 'Beat note'. In this problem we consider a more general case. Let fc > 0, fd > 0 and define a signal x as.
1) Calculate the open circuit voltage VOC (ZL removed) (magnitude and phase angle) 2) Calculate the Thevenin Equivalent impedance ZTH for this circuit (magnitude and phase angle)
Suppose q1 = 10. nC is located at the Cartesian coordinate point (4.0 m, 0.0 m, 0.0 m). A second charge q2 (-4.0 m, 0.0 m, 0.0 m) = -10. nC. If a test charge qt(0.0 m, 0.0 m, 3.0 m) = 0.10 nC
The LM358 op amp can be a single or dual supply op-amp. This mean that it can operate with just a single supply i.e. + 5 volt or with dual supplies i.e. (+ and -) 5 volt supplies. With a inverting configuration with dual supplies (+5v and -5v) bei..
Nanowire with square cross-section: Starting with the time-independent Schrodinger equation: (a) use separation of variables to obtain three ordinary differential equations (ODEs) (b) solve the ODEs and obtain the solution that satisfies the boundary..
calculate the losses in the transformer under these conditions. losses and efficiency when the transformer delivers its rated power to a load having a power factor of 90%
A HCS12 ATD is set to 10-bit unsigned mode. The voltage references are set to ground and 1.0V What is the ADT output for a temperature of 81 degrees The temperature sensor measures 0 to 100 degrees with an output of 10 mV/degree.
An n-channel JFET needs a NEGATIVE voltage applied to its GATE, relative to its SOURCE. If you have a single POSITIVE supply applied to the MASTER loop of a JFET, the mid point of the voltage divider will also be a positive voltage
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd