Determine the tension required

Assignment Help Mechanical Engineering
Reference no: EM13935258

The uniform bar OC of length L pivots freely about a horizontal axis through O. If the spring of modulus k is unstretched when C is coincident with A, determine the tension T required to hold the bar in the 45° position shown. The diameter of the small pulley at D is negligible.

568_determine the tension T required.png

Reference no: EM13935258

Questions Cloud

Describes two functions of dna : Explain how knowledge of DNA and technology is being used today to do things that we could not have done 50 years ago. Address how control of gene expression affects biotechnology.
Cultural or generational diversity : Whether it is cultural or generational diversity, create a PowerPoint presentation or MS MovieMaker project that identifies a diversity challenge of interest you.
Are you convinced that prions can be infectious agents : After browsing Prusiner's paper and/or checking out the website mentioned, are you convinced that prions can be infectious agents? Why or why not?
What are the causes effects and solution of misbehavior : What are the causes, effects and solution of misbehavior in the workplaces. What is the root causes of unwanted behaviors in an organization. What are the effects of misbehaviors of employees on the performance of organization. Define some key issues..
Determine the tension required : If the spring of modulus k is unstretched when C is coincident with A, determine the tension T required to hold the bar in the 45° position shown. The diameter of the small pulley at D is negligible.
Report on aspects of hr planning : This assignment is based on a specific organisational case, WWF, which is undergoing some changes. These changes have created a number of challenges for HRM practice.
What are the components of an operon : What are the components of an operon? What important regulator is not part of the actual operon? Know how operons are classified and how each type works (Inducible, Repressible, Positive, Negative.)
Develop a non-scientific calculator using c : Your calculator should only solve summation, subtraction, division, product, square root and square expressions. Utilizing the math.h header for your program, your calculator should start by prompting the user to enter a two-operand mathematical e..
What minimum number of replication unit in drosophila genome : DNA (3.5 x 108 base pairs) in diploid cells of Drosophila melanogaster is replicated in about 3 minutes. Assuming that all replication forks move at a constant rate of 104 base pairs per minute, what is the minimum number of replication units pres..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd